This board profiles adds board support example to OPEN-SMART 1.8INCH
LCD Driver IC: ST7567 Logic Level: 3.3V
Signed-off-by: Alan C. Assis <acassis@gmail.com>
This patch introduces CONFIG_CC1101_SPIFREQ_BURST and
CONFIG_CC1101_SPIFREQ_SINGLE to Kconfig, allowing users to override
the default SPI frequencies for the CC1101 wireless driver.
Previously, these values were hardcoded to 6.5 MHz and 9.0 MHz
respectively. While these are safe defaults for many setups, specific
hardware designs, high routing capacitance, or platforms utilizing
internal GPIO switching matrices (such as the ESP32) can suffer from
signal integrity degradation at these speeds. By exposing these to
Kconfig, users can easily adjust the clock speeds to match their
hardware capabilities without modifying the core driver source.
Impact:
- Build: Adds two new Kconfig options under WL_CC1101.
- Runtime: Retains 6.5 MHz / 9.0 MHz defaults. Behavior only changes
if overridden via menuconfig.
Testing:
- Built with default values and custom Kconfig overrides.
- Hardware Testing: Tested on a sub-optimal platform utilizing an
internal GPIO matrix (ESP32). The CC1101 failed to load at the
default 6.5/9.0 MHz due to signal integrity issues. Downclocking
the frequencies to 4.0 MHz via Kconfig successfully restored
signal integrity and allowed the driver to initialize and operate
normally.
Signed-off-by: Chip L. <chplee@gmail.com>
Add nxboot bootloader board integration for nucleo-h743zi.
nxboot uses a three-slot layout (primary, secondary, tertiary) with
no scratch partition.
- add STM32_APP_FORMAT_NXBOOT board support and nxboot-specific OTA
slot defaults
- gate scratch partition configuration on MCUboot, where it applies
- select nxboot linker scripts in the board build logic
- add tertiary OTA partition support in stm32_progmem.c
- add nxboot-loader and nxboot-app defconfigs and linker scripts
- validate the fixed nxboot flash layout used by this board so
mismatched config values fail at build time instead of producing
a silently broken image
Signed-off-by: Neil Berkman <neil@xuku.com>
This PR addresses several portability and technical debt issues in the mnemofs filesystem by resolving source-level TODO items.
Changes:
- Implemented a portable fallback for mfs\_clz (Count Leading Zeros) in fs/mnemofs/mnemofs.h using a binary search approach. This ensures compatibility with non-GCC compilers.
- Removed the redundant 8-bit mfs\_arrhash and consolidated hashing with the existing 16-bit mfs\_hash in mnemofs\_util.c.
- Removed the related TODO comments in mnemofs.h and mnemofs\_util.c.
- Fixed NuttX style (indentation and braces) in the fallback bit primitives.
Signed-off-by: Sumit <sumit6307@gmail.com>
This commit overhauls the CC1101 RF driver to address physical hardware
constraints, prevent register wrap-around overflows, and support accurate
dBm power scaling via the standard IOCTL interface.
What this change does:
1. Adds WLIOC_MSK and WLIOC_4FSK modulation support in `ioctl.h` and driver.
2. Replaces static PATABLE initialization with a dynamic Ramp-up curve
generator `cc1101_ioctl_apply_power()` based on lab calibration data.
3. Modifies WLIOC_SETTXPOWER and WLIOC_GETTXPOWER to process actual dBm
values with a nearest-match algorithm instead of raw array indices.
4. Removes DEBUGASSERT on user-space IOCTL pointers and replaces them
with strict -EFAULT checks.
5. Implements saturation clamping (e.g., mantissa to 256-511) to prevent
bitrate and frequency deviation calculation overflows.
6. Rebuilds volatile PATABLE memory upon SLEEP mode wake-up.
Why it is necessary & what it fixes:
- Fixes severe OOK modulation distortion and FSK spectral splatter caused
by statically assigned PATABLE indices.
- Fixes potential kernel panic in flat builds when IOCTL receives a NULL
pointer from user space.
- Fixes register wrap-around (silent failures) when users pass
out-of-bounds baud rate or FDEV values.
- Prevents RF silence after SLEEP mode due to PATABLE volatility.
- Resolves inaccurate power output when changing frequencies dynamically.
Impact:
Changes the behavior of CC1101 TX power and modulation IOCTLs to strictly
comply with standard `wlioc` definitions. Improves overall driver stability
and hardware safety.
Signed-off-by: Chip L. <chplee@gmail.com>
Three fixes to make LPUART1 work as NSH console on Nucleo-L552ZE-Q:
1. stm32l5_lowputc: add LPUART-specific BRR formula (256 * fCK / baud)
instead of reusing the standard USART divisor calculation.
2. stm32_boot: enable VDDIO2 and reconfigure LPUART1 GPIOs (PG7/PG8)
in board_initialize. The low-level setup runs before VDDIO2 is
enabled, so GPIOG writes silently fail.
3. stm32l5_serial: fix LPUART1 apbclock (PCLK1 not PCLK2), add
LPUART BRR branch in setformat, cast to uint64_t to prevent
32-bit overflow in (fCK << 8).
Also switch nsh defconfig from USART3 to LPUART1, add GPIO_LPUART1
pin definitions in board.h, and update board documentation.
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
This PR fixes a typo at `--help--` that causes NuttX Builds to fail, it should have been `---help---`. This is a recurring problem, NuttX CI uses a different way of handling NuttX Configs (it doesn't use `tools/configure.sh`)
https://github.com/lupyuen/nuttx-riscv64/actions/runs/22929878852/job/66548808341#step:5:161
```
$ tools/configure.sh rv-virt:nsh
arch/tricore/Kconfig:124: syntax error
arch/tricore/Kconfig:123: unknown option "--help--"
arch/tricore/Kconfig:124:warning: ignoring unsupported character ','
arch/tricore/Kconfig:124: unknown option "In"
```
Signed-off-by: Lup Yuen Lee <luppy@appkaki.com>
Add a new section documenting the TIOCSERGSTRUCT debug ioctl and CONFIG_SERIAL_TIOCSERGSTRUCT Kconfig option. The section covers enabling the feature, how the ioctl copies driver-internal state to user space, example usage with the 16550 UART driver, and a warning about the non-stable nature of exposed structures.
Signed-off-by: Arjav Patel <arjav1528@gmail.com>
This commit refactors the CC1101 driver's read interface to comply with
the standard NuttX wireless character driver API and introduces extended
hardware operation modes.
- Migrate `cc1101_file_read` to accept and populate the standard
`struct wlioc_rx_hdr_s` instead of returning raw byte arrays.
- Implement `cc1101_calc_rssi_dbm_x100` to preserve the hardware's
0.5 dBm RSSI precision when scaling to 1/100 dBm units, eliminating
the integer truncation loss present in the legacy calculation.
- Add `CC1101IOC_SETOPMODE` and `CC1101IOC_GETOPMODE` IOCTLs.
- Introduce four RF operation modes (`enum cc1101_opmode_e`):
1. NORMAL: Standard packet mode with hardware filtering.
2. PROMISCUOUS: Packet mode bypassing address filtering and retaining
packets with CRC errors.
3. SYNC_SERIAL: Bypasses FIFO, routes clock and data to GDO0/GDO2.
4. ASYNC_SERIAL: Bypasses FIFO, routes async data to GDO2.
- Fix the `GS2200M_FIRST` IOCTL block offset in `wireless/ioctl.h` and
allocate a dedicated IOCTL block for CC1101.
Signed-off-by: Chip L. <chplee@gmail.com>
Fix MAC address byte order by reversing 6 bytes after reading
from eFuse. Adjust offset logic to apply after byte reversal,
ensuring Ethernet MAC is base_mac +3. Comply with Espressif's
MAC address generation specification for ESP32S3
Signed-off-by: nuttxs <zhaoqing.zhang@sony.com>
This commit adds documentation entries for ESP32-P4 chip and its
board (ESP32-P4 Function-EV-Board).
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
This commit adds support for the Espressif's RISC-V-based ESP32-P4
chip along with its ESP32-P4-Function-EV-Board board.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
- Added functionality to read patch content from stdin when using the '--stdin' option with the '-p' flag.
- Updated usage instructions to clarify the new stdin option for patch checks.
- Improved error handling for unsupported combinations of options.
Signed-off-by: Arjav Patel <arjav1528@gmail.com>
- Updated the check workflow to conditionally include a '-b' option for breaking change enforcement based on PR labels.
- Modified the checkpatch script to support reading commit messages from stdin when using the '-m -g' flags.
- Improved usage instructions to clarify the new stdin option for commit message checks.
Signed-off-by: Arjav Patel <arjav1528@gmail.com>
- Introduced a new flag '-b' to enforce breaking change format in commit messages.
- Added checks to ensure that breaking change commits start with '!' and contain 'BREAKING CHANGE:' in the body before 'Signed-off-by'.
- Updated usage instructions to reflect the new breaking change option.
Signed-off-by: Arjav Patel <arjav1528@gmail.com>
Increase default TX power from 14 to 17 dBm and enable CRC
by default to improve link reliability and data integrity.
Signed-off-by: Arjav Patel <arjav1528@gmail.com>
Previously, the ST7796 driver required the board to pass a struct
st7796_config_s at initialization time, carrying display resolution,
color depth, orientation (MADCTL), BGR flag, SPI frequency, and
initial rotation.
All of these are chip-level properties, not board wiring details.
This created an awkward split: board code computed MADCTL values,
selected BPP, and derived effective resolution depending on orientation
(knowledge that belongs exclusively in the generic driver).
This commit removes that split entirely, following the same pattern used
by the ST7789 driver in drivers/lcd/Kconfig. It also implements the
getpower/setpower interface for standard framebuffer power management.
What was changed (per file):
drivers/lcd/Kconfig:
- Added a full 'if LCD_ST7796' ... 'endif # LCD_ST7796' block containing
all chip-level configuration.
- Includes LCD_ST7796_XRES/YRES, LCD_ST7796_BPP, LCD_ST7796_FREQUENCY,
LCD_ST7796_SPIMODE, LCD_ST7796_BGR, LCD_ST7796_INVCOLOR,
and orientation/rotation choices.
drivers/lcd/st7796.c:
- Removed struct st7796_config_s from struct st7796_dev_s.
- Moved struct st7796_cmd_s from public header to Private Types.
- Added compile-time macros derived from Kconfig:
ST7796_XRES/YRES (swapped for landscape),
ST7796_MADCTL_BASE,
ST7796_SPIMODE,
ST7796_BYTESPP,
ST7796_COLORFMT.
- Implemented st7796_getpower() and st7796_setpower() using the
st7796_board_power() board callback.
- Registered power functions in st7796_fbinitialize() vtable.
- Updated st7796_init_display() to make INVON/INVOFF conditional on
CONFIG_LCD_ST7796_INVCOLOR.
- Simplified st7796_fbinitialize() signature to only take
'struct spi_dev_s *spi'.
include/nuttx/lcd/st7796.h:
- Removed legacy macros (ST7796_XRES_RAW, etc.) and configuration
structures.
- Updated st7796_fbinitialize() prototype.
- Added st7796_board_power() callback prototype.
- Removed private implementation details from the public header.
boards/arm/stm32h7/nucleo-h753zi/Kconfig:
- Removed chip-level menus (settings, orientation) now handled by the
generic driver.
- Retained only board-specific wiring concerns (pins and SPI bus).
boards/.../stm32_st7796.c:
- Removed g_st7796_config and associated board-side macros.
- Updated st7796_fbinitialize() call to the new signature.
- stm32_st7796_flush_fb() now queries effective resolution
via g_fb_vtable->getvideoinfo().
Verified on nucleo-h753zi:
Orientation: Landscape (480x320),
Rotation: 180 deg,
BGR: enabled,
INVCOLOR: disabled,
BPP: RGB565,
Frequency: 40 MHz.
Making INVCOLOR a Kconfig option (default n) fixes cases where panels
previously showed inverted colors due to hardcoded INVON.
Signed-off-by: vrmay23 <vmay.sweden@gmail.com>
* Fix GPIO unspecified behavior on some GPIO ports.
* Fix GPIO undefined behavior caused by uncleared set or reset bits.
Signed-off-by: Saurav Pal <resyfer.dev@gmail.com>
