Inspired by Linux's way, we also create VLAN devices for managing VLAN,
which will become interfaces like `eth0.58`.
QinQ is also supported, we can create VLAN devices above another VLAN
devices, like `eth0.100.101` (or even `eth0.1.2.3.4`, also supported on
Linux).
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
after the network card is turned off, read and write operations need
to return -ENETDOWN, and it is necessary to wake up the waiting read
and write operations.
Signed-off-by: wangchen <wangchen41@xiaomi.com>
Add support for the page erase (PE), sector erase (SE) and chip erase
(CE) dedicated commands on supported devices.
They can be triggered using the corresponding IOCTL commands
EEPIOC_PAGEERASE, EEPIOC_SECTORERASE and
EEPIOC_CHIPERASE.
On unsupported devices, this is equivalent to writing a full page,
sector, or the entire EEPROM to 0xFF.
Signed-off-by: Antoine Juckler <6445757+ajuckler@users.noreply.github.com>
The bytes of color should be sent in an opposite order in st7789_fill
function if the driver operates in 3 wire mode.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Add complete driver support for the QST QMI8658 6-axis IMU sensor featuring
3-axis accelerometer and 3-axis gyroscope with I2C interface and uORB
integration.
Key features implemented:
* Full I2C communication with configurable frequency (default 400kHz)
* Multiple accelerometer ranges (±2g, ±4g, ±8g, ±16g) and ODR settings
* Multiple gyroscope ranges (±16 to ±1024 dps) with high ODR support
* Low-pass filter configuration for both sensors
* Temperature sensing with 16-bit resolution
* Self-test capability for both accelerometer and gyroscope
* Calibration-on-demand support with offset registers
* FIFO buffer management (framework ready)
* Interrupt-driven and polling mode support
* Complete uORB integration with sensor_accel and sensor_gyro topics
Driver components added:
* Core driver implementation (qmi8658_uorb.c) with register operations
* Header file with register definitions and scale factors (qmi8658.h)
* Kconfig options for driver configuration and polling mode
* Build system integration (CMakeLists.txt, Make.defs)
* Comprehensive documentation with API reference and usage examples
The driver follows NuttX sensor framework conventions and provides
robust error handling, mutex protection, and comprehensive debugging
support through CONFIG_DEBUG_SENSORS.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
- Rohm BH1750FVI Ambient Light Sensor support
Correct order dependency
Factoring out common dependencies
- STMicro LSM6DSO32 IMU sensor
if SENSORS_LSM6DSO32 for common dependency
- Broadcom APDS-9922 proximity and ambient light sensor
if SENSORS_APDS9922 for common dependency
- MEAS MS58XX altimeters sensor
if SENSORS_MS58XX for common dependency
Signed-off-by: simbit18 <simbit18@gmail.com>
This commit adds SPI_SETDELAY interface if CONFIG_SPI_DELAY_CONTROL
option is set. This allows to set custom delay between SPI transfers,
chip selects and so on.
Default values are set to 0. W25 SPI NOR flash works with them and
I haven't found any other values in the datasheet.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This reverts the removal of ndelay_accurate from #14450, since as
mentioned in #17011, this fails to consider the `sim` architecture
where CONFIG_BOARD_LOOPSPERMSEC was set to 0 because of reliance on the
accurate implementations of the up_delay functions. All the commit did
was remove a more accurate implementation in favour of a less accurate
one.
Signed-off-by: Matteo Golin <matteo.golin@gmail.com>
Add EEPIOC_SETSPEED ioctl acting like the MTDIOC_SETSPEED ioctl. The
default frequency is settable in the Kconfig.
Add xx25xx SPI delay control configurations.
Signed-off-by: Antoine Juckler <6445757+ajuckler@users.noreply.github.com>
This adds ability for read and write operations to work with messages
aligned to configured number of bytes. This has few different use
cases.
The alignment is specified as unsigned integer and can be changed with
ioctl command CANIOC_SET_MSGALIGN. The current value can be queried by
CANIOC_GET_MSGALIGN command.
The default value for the message alignment is 1. This will provide
behavior consistent with current one. Thus messages are placed to the
buffer right after data of the previous one. The same applies for
writes.
The special alignment value 0 disables read and write of multiple frames. Thus
read will always return at most one message and write will always write
only one message even if larger buffer size is provided.
Another use case is if message alignment is set to exactly message
representation size (`sizeof(struct can_msg_s)`). This allows writing
and reading arrays of messages.
Other values provide even more advanced and specialized use cases, such
as optimizations if architecture has to emulate some non-aligned
accesses, there alignment of for example 4 bytes could provide
performance boost.
The original motivation behind this is was compatibility with socket
CAN. It is easier to port applications to NuttX's CAN driver if only one
frame is provided at the time. This solution was suggested by Pavel Pisa
<pisa@fel.cvut.cz> as a more versatile variant of plain boolean
disabling the multiple frame retrieval.
Signed-off-by: Karel Kočí <kkoci@elektroline.cz>
This commit fixed oneshot callback for non-tickless using tick-aligned
absolute oneshot interfaces.
Signed-off-by: ouyangxiangzhen <ouyangxiangzhen@xiaomi.com>
This commit introduce new clockdevice interfaces for oneshot.
- It can represent both `timer` and `alarm`.
- It simplifies the implementation of timer driver. Timer driver do not need considering the time conversion between clock count, tick and timespec.
- It sets timer align to the tick boundary to improve timer accuracy.
- It can avoid using 64-bit division during timer expiration interrupt, improves performance and reduces interrupt latency.
- It considers almost all multiplication overflow problems in time conversion without processing at the driver.
Signed-off-by: ouyangxiangzhen <ouyangxiangzhen@xiaomi.com>
Adds a device ID to ee25xx_initialize, which is stored in the
ee25xx_dev_s structure. This ID is used when calling SPI_SELECT.
The implementation is based on the handling of the chip select in
mtd/ramtron.c
This change is NOT backward compatible: the function signature has changed
Signed-off-by: Antoine Juckler <6445757+ajuckler@users.noreply.github.com>
Adds a device ID to at25ee_initialize, which is stored in the
at25ee_dev_s structure. This ID is used when calling SPI_SELECT.
The implementation is based on the handling of the chip select in
mtd/ramtron.c
This change is NOT backward compatible: the function signature has changed
Signed-off-by: Antoine Juckler <6445757+ajuckler@users.noreply.github.com>
As reported by a user in Discord channel selection BMI160 with SPI
interface still showing the I2C configuration. This patch fixes it.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
It acts as register_driver but also populates the inode size.
This allows to return a non-zero size when calling stat() on an eeprom
driver.
The conditions (CONFIG_PSEUDOFS_FILE or CONFIG_FS_SHMFS) for the
declaration of the inode size field have also been removed so that other
drivers can populate this field in the future.
Signed-off-by: Antoine Juckler <6445757+ajuckler@users.noreply.github.com>
The empty FIFO can happen only in two cases. Either there is some
inconsistency that made rx_sem ready but buffer is empty (that might
happen if multiple reads are blocked in parallel, or just due to the bug
in the logic), or if close is used. Until now the 0 would be returned
and thus EOF. The error is not EOF and actually it is still possible to
read afterwards. Thus we for sure should not signal EOF for the first
cause. The second cause for close matches the behavior that is expressed
even on glibc for some file descriptors (the waiting read will commonly
get error EINVAL there). We can't decide on the real cause of this
situation and thus we always report EIO error and thus generic
input/output error.
Signed-off-by: Karel Kočí <kkoci@elektroline.cz>
The previous version of the code was posting the semaphore every time
the value was less or equal to the zero. In case there is read already
waiting on the semaphore the value will be -1. The first frame will post
the value to 0 and thus unblocking the waiting read. The read will take
frames out of FIFO. During that time if next frame is received it will
be placed to the FIFO but because rx_sem has value 0 at that time it
will be posted to value 1. Once read finishes the execution it will
check if there is something still in the FIFO and posts semaphore back
(expecting that the value is 0) thus increasing value to 2. Thus we end
up with read being unblocked once more triggering 'RX FIFO sem posted
but FIFO is empty.' error branch and returning zero (signaling EOF?).
The intuitive fix is to check the value of the semaphore before posting
it in the read's tail. This could have race condition case when
interrupt is delivered between nxsem_get_value and nxsem_post and
can_receive is called.
This fix instead uses the same condition to detect if semaphore must be
posted as read does. Thus we check if previously the FIFO was empty. We
post the semaphore on in case FIFO was initially empty, otherwise we
expect semaphore to be fully managed by can_read.
Signed-off-by: Karel Kočí <cynerd@email.cz>
The message passed to the write can have `cm.hdr.ch_rtr` set and if
nonzero DLC is specified in the frame then invalid number of bytes is
removed from the buffer as RTR frames do not have any data even when DLC
is nonzero.
This was tested on SAMv7 (mcan). With this change a custom RTR can be
sent.
Signed-off-by: Karel Kočí <cynerd@email.cz>
The message size is being calculated from the message itself. If
application sets value cm_hdr.ch_dlc greater than buflen (that is
size_t) then calculation in while condition underflows and multiple
messages are attempted to be sent.
This check prevents that by verifying that the message size that was
encoded in the dlc is not greater than indicated size of the buffer.
Signed-off-by: Karel Kočí <cynerd@email.cz>
Add documentation describing the purpose and behavior of early_syslog(),
which provides a minimal logging facility available during early system
initialization or system down.
Signed-off-by: Chengdong Wang wangchengdong@lixiang.com
Introduce early_syslog() to enable basic logging during the very early
boot or system down stages, when the full syslog subsystem is not yet
available.
Signed-off-by: Chengdong Wang wangchengdong@lixiang.com
This is the case for USB2517 USB HUB. Also improved the driver to
avoid mistakes: initially I changed g_id[3], but the in register
there is another field where we need to pass this size again. So
it is better to use ARRAY_SIZE() macro to avoid mistakes.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
Introduce a new function nxsched_tick_expiration() to replace
nxsched_alarm_tick_expiration(). The new function provides a
common implementation that can be shared by both the alarm
and timer architectures.
This change reduces code duplication and provides a unified
function that can be directly reused.
Signed-off-by: Chengdong Wang <wangchengdong@lixiang.com>
Nuttx currently has 2 types of sleep interfaces:
1. Signal-scheduled sleep: nxsig_sleep() / nxsig_usleep() / nxsig_nanosleep()
Weaknesses:
a. Signal-dependent: The signal-scheduled sleep method is bound to the signal framework, while some driver sleep operations do not depend on signals.
b. Timespec conversion: Signal-scheduled sleep involves timespec conversion, which has a significant impact on performance.
2. Busy sleep: up_mdelay() / up_udelay()
Weaknesses:
a. Does not actively trigger scheduling, occupy the CPU loading.
3. New interfaces: Scheduled sleep: nxsched_sleep() / nxsched_usleep() / nxsched_msleep() / nxsched_ticksleep()
Strengths:
a. Does not depend on the signal framework.
b. Tick-based, without additional computational overhead.
Currently, the Nuttx driver framework extensively uses nxsig_* interfaces. However, the driver does not need to rely on signals or timespec conversion.
Therefore, a new set of APIs is added to reduce dependencies on other modules.
(This PR also aims to make signals optional, further reducing the code size of Nuttx.)
Signed-off-by: chao an <anchao.archer@bytedance.com>
Add a new ioctl to get the count of paninfo
The framebuffer is usually in high-speed RAM. Getting the paninfo
count can help us get the idle state of the framebuffer so that we
can temporarily use this memory.
Signed-off-by: yushuailong1 <yushuailong1@xiaomi.com>
This protects the driver in case multiple threads are trying to initialize
or uninitialize the cdcacm concurrently.
Note that this only protects the case when the private pointer is not managed
outside the kernel. If someone has acquired the pointer to the driver and uses
that, it also needs to manage the protection itself if needed.
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
clock_systime_timespec() always returns 0, so there is no need to
check the return value in the caller code, let us remove the return
value directly.
Signed-off-by: chao an <anchao.archer@bytedance.com>
