Register GPT0 (32-bit) as /dev/timer0 and GPT9 (16-bit) as /dev/timer1
during bring-up.
Register the Arduino Uno shield header's D2-D5 as inputs and D6-D13 as
outputs through the generic GPIO expander driver, as /dev/gpio0-3 and
/dev/gpio4-11.
Add the ek-ra8m1:timer-gpio configuration (nsh plus both GPT channels,
the GPIO support above, and apps/examples/gpio and
apps/examples/timer_gpio), used to validate the GPT timer driver on
hardware with an oscilloscope.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Assisted-by: Claude:claude-sonnet-5
Signed-off-by: leocafonso <leocafonso@gmail.com>
There were some bits erroneously copied from imx9. For IMXRT1180, the
GPIO_AD* and GPIO_AON* pads should have SRE, DSE, PUE, PUS and ODE bits
on SW_PAD_CTL_PAD register.
The GPIO_EMC_*, GPIO_SD_*, GPIO_B1_* and GPIO_B2_* have a bit different fields,
PDRV, PULL and ODE.
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
Implement the same initial clock configuration as what imxrt1176 has. Make an own table
for PLL and root clock configurations for m33 and m7 targets. For the PLLs the code still
only supports configuring the ARM_PLL.
The difference to imxrt1176 is, that instead of just boolean .enable field, this table
uses an .action field with 3 states: CONFIGURE, DISABLE and IGNORE. The reason is,
that some root clocks can't be just forcefully stopped, but need a root-clock-specific
sequence. This is solved by just leaving these clocks marked as IGNORE, so they retain
their current state.
Specifically, disabling the SEMC and NETC roots by M33 will prevent the M7 from booting.
Also FLEXSPI shouldn't be touched, if the code is being executed from there.
Also add a function for enabling 24 MHz oscillator clock, and an extendable function to
enable the clock sources based on the clock configuration table.
Assisted-by: Claude Code
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
Add board support for the EK-RA8M1 evaluation kit with nsh and
nsh-leds configurations, linker script, LED support and bring-up.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Signed-off-by: leocafonso <leocafonso@gmail.com>
Add CMake build support for the stm32l476vg-disco board by introducing
board and source CMakeLists.txt files.
This allows the stm32l476vg-disco:nsh configuration to build successfully
with the CMake build system.
Fixes: #20366
Signed-off-by: Ahmed Ashraf NourEldeen <a.programmer55559@gmail.com>
A module's D-Space is separate from its I-Space, so its read-only data is not
at a fixed offset from its text. GCC assumes that it is and loads a string
literal PC-relative, which reads I-Space at run time. A module could
therefore carry no string and reach no static.
lm3s6965-ek has had -mno-pic-data-is-text-relative in its own Make.defs since
2021 (issue #3737), and the CMake build gives it to every PIC configuration,
so the flag moves to where it belonged and the board's copy goes. That copy
also probed for GCC older than 4.9.4, which NuttX no longer supports. Clang
has no such option, hence the guard.
Assisted-by: Claude Opus 5 (1M context) <noreply@anthropic.com>
Signed-off-by: Marco Casaroli <marco.casaroli@gmail.com>
Suppress the peer notifications while a ring keeps delivering work, batch
the receive completions into one kick per burst and drop the redundant
txdone signal from the transmit path. Validate the peer controlled frame
lengths, accept descriptor chains on both lanes, keep every ring access on
the upper half's work thread so the interrupt context callbacks stay lock
free, and prefer the MAC from the configuration space, falling back to the
Kconfig address or a random one.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
The TRDC (Trusted Resource Domain Controller) configuration should be completely
driven by the board configuration, and not hard-coded:
- Add tables for the current GPIO configuration and MDA configuration.
- Fix the GPIO configurations for M7; previously GPIO access from M7 was
denied because of secure/nonsecure setting.
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
Expose the RTL8730E general-purpose UARTs through the shared Ameba
serial driver (arch/arm/src/common/ameba/ameba_uart.c) by adding the
chip-specific glue, build wiring and a board port table. The change is
gated by CONFIG_AMEBA_UART (default disabled); the LOG-UART keeps the
console and /dev/ttyS0.
Chip glue (ameba_uart_chip.h) supplies the three UART controller
register bases, GIC IRQ numbers (SPI 50/51/52 -> NuttX IRQ 82/83/84),
APB clock masks and pin-mux codes. The board registers UART0-2 as
/dev/ttyS1-3 at 115200 8N1; UART3 is reserved for Bluetooth. Pads are
picked from the EVB break-out (the UART crossbar maps each controller to
many pads, so this is purely a board choice).
Also fix an RX-timeout interrupt storm in the shared driver: the
RX-timeout status (LSR bit9) is latched and is not cleared by draining
the RX FIFO, so on a level-triggered GIC (RTL8730E) the ISR must
explicitly write TOICF, matching the vendor SDK serial_api.c. The
extra register write is harmless on the NVIC-based M33 Ameba parts and
was regression-tested on them.
Signed-off-by: dechao_gong <dechao_gong@realsil.com.cn>
Assisted-by: Claude <noreply@anthropic.com>
Under sustained dual-core critical-section traffic (e.g. several UART
ISRs) the two Cortex-A32 cores live-lock trading failed STREX. The
generic critical-section lock g_cpu_irqlock (an LDREX/STREX spinlock)
and the plain non-atomic bitmap g_cpu_irqset are defined back-to-back
in sched/irq/irq_csection.c and land in the same 64-byte cache line.
The A32 exclusive monitor reserves a full cache line, so one core's
ordinary store to g_cpu_irqset clears the other core's LDREX
reservation on g_cpu_irqlock.
Separate the two symbols onto their own cache lines in the board link
script, leaving the generic scheduler source untouched (relies on the
toolchain emitting per-object -fdata-sections).
Signed-off-by: dechao_gong <dechao_gong@realsil.com.cn>
Assisted-by: Claude <noreply@anthropic.com>
A MIMXRT1176 flight controller built to the Pixhawk FMUv6X-RT standard, so
the port also covers the NXP MR-VMU-RT1176.
Board data comes from PX4, which already carries it as a NuttX board config:
the clock tree, the LPUART1 pinmux, and the Macronix octal flash
configuration block the boot ROM reads at offset 0x400.
The board ships with the PX4 bootloader in the first 128 KB of QSPI, so the
image links at 0x30020000 and is loaded by it rather than written to the
flash base. The console is CDC/ACM as on teensy-4.x, so a USB cable is the
only thing needed to run NuttX here.
Signed-off-by: Royyan Zahir <royzah@gmail.com>
The flexspi_nor_config_s was missing four fields, resulting the fields after the
missing ones being read from wrong positions.
Align the struct properly according to the reference manual.
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
Correct switch and declaration indentation, separate declarations from code,
and wrap a long comment in the SPI driver. Fix the timer driver and both
STM32L5 board LED implementations checked by the commonization PR.
These are formatting changes only.
Signed-off-by: raiden00pl <raiden00@railab.me>
Select STM32_HAVE_IP_GPIO_M33_V1 and STM32_HAVE_IP_EXTI_M33_V1 and
drop the family GPIO and EXTI sources and headers in favor of the
common Cortex-M33 v1 implementation.
Define both EXTI register banks and retain the named bit definitions.
Use shared line and selector helpers without per-line conditionals.
Clear each GPIO selector with the same byte mask, as the H5 driver does.
Cover both 32-bit banks and H5 line inventories for later migration.
The common EXTI driver also routes the selected port through EXTICR,
which the family driver never programmed, so GPIO interrupts now work
on ports other than GPIOA.
Signed-off-by: raiden00pl <raiden00@railab.me>
Assisted-by: Claude Code
Wire the shared ameba_gpio driver to the RTL8730E CA32 core.
The CA32 replaces the vendor CA32 OS as BL33; the SDK startup that
normally initialises GPIO_PORTx[] never runs under NuttX. The three
GPIO port base addresses are patched at runtime inside
rtl8730e_gpio_initialize() before any ROM GPIO function is called.
GPIO_INTStatusGet and GPIO_INTStatusClearEdge are absent from the
RTL8730E ROM and are provided as static inline helpers in the new
ameba_gpio_chip.h.
Key changes:
- ameba_gpio_chip.h (new): chip parameters, split AMEBA_APBPERIPH_GPIO
/ AMEBA_APBPERIPH_GPIO_CLK bits, inline INTStatus helpers
- ameba_gpio.c: add AMEBA_APBPERIPH_GPIO_CLK fallback macro so chips
with separate periph/clock enable bits work without driver changes
- Make.defs: enable ameba_gpio.c + rtl8730e_flash_stubs.c + lib_rom.a
under CONFIG_AMEBA_GPIO; consolidate flash_stubs into GPIO||FLASH_FS
- ameba_board.mk: remove duplicate lib_rom.a (Make.defs is authoritative)
- rtl8730e_flash_stubs.c: make _strcmp weak; delegate Pinmux_Config to
lib_rom.a's _Pinmux_Config so GPIO pad mux is configured correctly
- Kconfig: source common/ameba/Kconfig to expose CONFIG_AMEBA_GPIO
- dramboot.ld: include .sramdram.only.data in .data so GPIO_PORTx[] is
copied to RAM by the normal arm_data_initialize() path
- scripts/Make.defs: extend --no-warn-mismatch to GPIO and WiFi configs
- rtl8730e_gpio.c (new): pin table (PB19 output /dev/gpio0, PB20 input
/dev/gpio1, PB11 falling-edge interrupt /dev/gpio2) + GPIO_PORTx patch
- configs/gpio/ (new): defconfig for GPIO example verification
- nxstyle.c: add _Pinmux_ to mixed-case whitelist (ROM symbol)
Hardware verified on RTL8730E CA32:
- PB19 output write 0/1, readback matches
- PB20 input reads PB19-driven level
- PB11 falling-edge interrupt triggers correctly
Signed-off-by: dechao_gong <dechao_gong@realsil.com.cn>
Assisted-by: Claude <noreply@anthropic.com>
nsh plus networking over the rptun/virtio-net link to the A53: enables
DRIVERS_VHOST_NET with the buffer sizing the link needs (IOB pool and chains,
NET_LL_GUARDSIZE covering the ethernet and virtio-net headers) and ICMP
sockets for ping. Also gives CI an in-tree configuration that compiles the
vhost-net driver.
Verified on t3-gem-o1: ifup, then ping from the peer with 0% loss.
Assisted-by: Claude Code:claude-fable-5
Signed-off-by: Ulaş Sertan Kemeç <sertan.usk@gmail.com>
Adopt the zbus message bus on the linum-stm32h753bi (first adopter
board):
- scripts/flash.ld: include the iterable sections common fragments
(2 lines: common-rom.ld inside .text, common-ram.ld inside .data).
- configs/zbus/defconfig: board configuration enabling zbus with all
observer types, the zbus example and its cmocka test suite
(./tools/configure.sh linum-stm32h753bi:zbus).
- Board documentation: describe the new configuration.
Validated on hardware: the 16-test cmocka suite passes twice in the
same boot and the zbus example produces the expected output.
Assisted-by: Claude Code
Signed-off-by: Jorge Guzman <jorge.gzm@gmail.com>
platform_autoconf.h is a hand-maintained minimal header that provides the
SDK #defines required by the fwlib sources compiled during PREBUILD. Unlike
the other Ameba ICs (which use ameba_gen_autoconf.sh to regenerate it from
SDK menuconfig), RTL8730E uses a static file because the amebasmart SDK
does not ship a pre-generated autoconf and running menuconfig in CI is not
feasible.
The file was previously gitignored along with all other prebuilt/ artifacts,
so CI had no platform_autoconf.h on a clean clone, causing:
fatal error: platform_autoconf.h: No such file or directory
Fix: add !platform_autoconf.h exception to prebuilt/.gitignore and track
the file in git. Local clean build verified (nuttx.bin 550 KB generated).
Signed-off-by: dechao_gong <dechao_gong@realsil.com.cn>
Assisted-by: Claude <noreply@anthropic.com>
Two CI issues in the RTL8730E (AmebaSmart CA32) port:
1. PREBUILD used $(ARCHOPTIMIZATION) which injects --param=min-pagesize=0
on GCC>=12. arm-none-eabi-gcc in CI does not recognise this flag.
Fix: replace $(ARCHOPTIMIZATION) with explicit -Os -ffunction-sections
-fdata-sections in both the fwlib and wifi PREBUILD loops, matching the
pattern already used by the other Ameba ICs (rtl8721dx/8720f/8721f).
2. boards/arm/rtl8730e/rtl8730e_evb/configs/nsh/defconfig was out of sync
with `make savedefconfig` output (missing CONFIG_ARCH_CHIP_RTL8730E_CA32,
wrong ordering of several NETUTILS options, and redundant entries that
are auto-selected by Kconfig). Regenerated with olddefconfig+savedefconfig.
Signed-off-by: dechao_gong <dechao_gong@realsil.com.cn>
Assisted-by: Claude <noreply@anthropic.com>
Add the rtl8730e_evb (RTL8730E Evaluation Board) with an nsh configuration
that demonstrates the RTL8730E baseline feature set:
- Dual-core SMP (CONFIG_SMP=y, CONFIG_SMP_NCPUS=2)
- Wi-Fi station and SoftAP via wapi
- DHCP client (wlan0) and DHCP server (wlan1/AP mode)
- littlefs persistent storage at /data on SPI NOR flash
- iperf2 TCP/UDP throughput measurement
- NSH console over the LOG-UART
Board formerly named ca32-evb; renamed to follow the rtlXXXX_evb
convention used by all other Ameba boards.
Signed-off-by: dechao_gong <dechao_gong@realsil.com.cn>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Replace the CMake skeleton with full SDK build machinery, mirroring
the make-side ameba_board.mk. RTL8730E differs from the KM4-based
ICs in three ways that prevent a direct include(ameba_board.cmake):
- No SDK autoconf / image2 ldscript generation: the board uses its own
dramboot.ld and a static prebuilt platform_autoconf.h
- No NP firmware build: KM0/KM4 are prebuilt blobs in prebuilt/
- No -mcmse: CA32 is ARMv7-A, not Cortex-M33; uses -DCONFIG_ARM_CORE_CA32
The ameba_build_lib() helper (adapted from ameba_board.cmake) compiles
SDK sources with an isolated flag set into libameba_fwlib.a and
libameba_wifi.a, avoiding NuttX header conflicts.
Key additions:
- libameba_fwlib.a: arch.c + log.c + sscanf_minimal.c always; IPC for
WiFi/FlashFS; ameba_flash_ram.c for FlashFS
- lib_rom.a linked for GPIO or FlashFS (GPIO_Init, Pinmux_Config, etc.)
- libameba_wifi.a + prebuilt WHC host libs for WiFi
- VFS1 geometry extracted from platform_autoconf.h via
target_compile_definitions (set_property(SOURCE) has scope issues in
NuttX's include()-based CMake structure)
- `flash` target calls ameba_smart_flash.sh
Verified: gpio (1186 targets) and nsh (1530 targets) configs both
build cleanly; /data mounts at correct 2 MB partition size.
Signed-off-by: dechao_gong <dechao_gong@realsil.com.cn>
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
RTL8730E has dual Cortex-A32 cores (CA32) in the AP domain. Core1 is
powered off by default and requires an explicit HSYS power-on sequence
before ATF SP_MIN can service the PSCI CPU_ON call. Without it, SP_MIN
writes the entry point to the mailbox and times out waiting for Core1 to
poll it.
Add rtl8730e_core1_power_on() that mirrors SDK smp.c:rtk_core1_power_on():
assert reset, assert isolation, two-stage power-on with up_udelay() for
correct 50/50/500/50 us timing, then release isolation and reset. Call it
from up_cpu_start() before psci_cpu_on().
Enable CONFIG_SMP / CONFIG_SMP_NCPUS=2 / CONFIG_ARM_PSCI in the nsh
defconfig.
Enabling SMP also exposed a latent WHC skb alignment bug: the Realtek
WHC WiFi driver keeps the AP/NP DDR views coherent with by-VA
DCache_Clean/Invalidate at SKB_CACHE_SZ (64 on RTL8730E) granularity,
which requires every skb buffer to be cache-line aligned. The port had
omitted CONFIG_MM_DEFAULT_ALIGNMENT (defaulting to 8; the 8721Dx parts
set 32), so heap-allocated skb buffers were unaligned and the cache
maintenance spilled onto the neighbouring skb struct, corrupting its
immutable buf pointer (seen as skb->buf = 0x05 and a TX memcpy data
abort on "renew wlan0"). This was harmless on single core -- the
non-shareable DDR mapping made the stray maintenance a no-op -- but the
SMP shareable mapping plus real dual-core concurrency turned it into a
hard fault. Set CONFIG_MM_DEFAULT_ALIGNMENT=64 in the nsh defconfig.
Hardware verified on RTL8730E (C-cut): /proc/cpuinfo shows both processor 0
and processor 1; getprime 2 completes two concurrent threads in ~573 ms
(same as single-thread), confirming true parallel execution across both cores.
"renew wlan0" now obtains a DHCP lease (192.168.1.101) without faulting.
Assisted-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: dechao_gong <dechao_gong@realsil.com.cn>
Add NuttX support for the Realtek AmebaSmart (RTL8730E) running on the
CA32 (Cortex-A32) application core, with the KM4/KM0 cores kept as
vendor firmware (KM4 acts as the WiFi network processor over WHC IPC).
Stage 1 bring-up, hardware verified:
- CA32 boot / exception vectors / MMU + page allocator / heap
- LOGUART console (RX via KM0-owned IPC + shared memory)
- IRQ controller, timer, serial
- On-chip SPI NOR flash MTD -> littlefs mounted at /data
- WHC-host WiFi netdev (STA): scan / connect / DHCP, verified end to
end (association -> 4-way -> DHCP -> ping, bidirectional TCP)
IC-agnostic Ameba glue is shared from arch/arm/src/common/ameba via a
relative VPATH entry (matching the rtl8721dx pattern), which also avoids
the empty mkdeps --dep-path that a leading-":" VPATH entry produced and
which intermittently broke parallel .ddc dependency generation.
The FIP packaging / flash image assembly is driven by
common/ameba/tools/ameba_smart_flash.sh from the board scripts.
Vendor blobs and build artefacts under the board prebuilt/ directory are
kept out of the tree via prebuilt/.gitignore.
Signed-off-by: dechao_gong <dechao_gong@realsil.com.cn>
Connects the R5F to Linux remoteproc over the NAVSS mailbox.
The mailbox ISR only drains the FIFO and acknowledges; OpenAMP delivery is
deferred to HPWORK, because the rpmsg rx path takes mutexes and allocates.
The resource table publishes two vdevs, rpmsg and virtio-net, leaving every
vring address FW_RSC_ADDR_ANY: Linux allocates them from the R5F DMA pool and
rejects fixed addresses outside it.
Shared IPC memory is mapped Non-cacheable, since the R5F is not coherent with
the A53 and cached mappings leave NuttX reading stale vring state.
Also drops the duplicate arm_mpu.c from CHIP_CSRCS.
Assisted-by: Claude Code:claude-fable-5
Signed-off-by: Ulaş Sertan Kemeç <sertan.usk@gmail.com>
CONFIG_EXAMPLES_COMP_DACPATH matched its Kconfig default value, which
make savedefconfig drops as redundant. The stale explicit line made
the committed defconfig differ from what a clean savedefconfig
produces, failing CI's defconfig-completeness check even though the
board builds fine either way.
Assisted-by: Claude:claude-sonnet-5
Signed-off-by: Daniel P. Carvalho <danieloak@gmail.com>
Implement ao_ioctl in stm32_comp_m3m4_v2.c to handle ANIOC_COMP_ENABLE and
ANIOC_COMP_DISABLE commands. Also add CONFIG_STM32_COMP_INIT_DISABLED to
allow keeping the comparator disabled after driver initialization until
explicitly enabled.
Update nucleo-g431kb:comp defconfig to enable CONFIG_EXAMPLES_COMP and
set default DAC path for comparator ramp verification.
Assisted-by: Gemini:gemini-2.5-pro
Signed-off-by: Daniel P. Carvalho <danieloak@gmail.com>
Add a standalone tool to create AHAB container for imxrt118x. This can
generate a trivial unsigned image without appending ELE.
The tool can be used to create bootable images for m33. To do anything
more complicated, the user needs to use the official SPSDK tool from
NXP.
Assisted-by: Claude Code:claude-opus-5-0
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
This adds the initial board configurattions for building NuttX for imxrt1189-evk.
Also add a script building the NXP container image for bootloaders (m33 images)
The board boots on Cortex-M33 core, for which there are two m33 targets: nsh-m33 and bl.
- "bl" target does basic initialization of ELE and TRDC and just releases the M7 to run
at 0x20080000.
- "nsh-m33" target just boots nuttx into nsh shell on m33
- The "nsh" target is for M7 core. It can be flashed at 0x20080000, and
it boots to nsh shell with a proper bootloader on m33 (the bl target does this).
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
Move RX timestamp storage from net_driver_s.d_rxtime into
iob_s.io_time so each IOB carries its own timestamp through
the stack. Remove old iob_trycopyin/iob_copyout timestamp
packing in CAN/PKT/UDP paths. Fix iob_clone_partial to copy
io_time before source pointer advances to NULL.
Signed-off-by: OceanfromXiaomi <zhaohaiyang1@xiaomi.com>
Signed-off-by: wenquan1 <wenquan1@xiaomi.com>
Switch CONFIG_INIT_ENTRYPOINT from nsh_main to nxinit's init_main for
the shell-capable configs (nsh, usbnsh) of waveshare-rp2040-zero and
waveshare-rp2040-lcd-1.28. nsh now runs as a "console sh" service
started by init.rc instead of being the top-level init task.
Add etc/init.d/init.rc to the shared common/src RCSRCS, gated on
CONFIG_ETC_ROMFS && CONFIG_SYSTEM_NXINIT, so one copy covers both
boards, plus a .gitignore for the etctmp files Board.mk generates from
it. The four defconfigs also set CONFIG_SYSTEM_NXINIT=y with its
Kconfig deps, CONFIG_ETC_ROMFS=y and CONFIG_FS_ROMFS=y.
nsh_main connected the CDC/ACM gadget itself via
boardctl(BOARDIOC_USBDEV_CDCACM); init_main does not, so the usbnsh
configs would otherwise come up with no USB console. Run sercon from
init.rc and enable CONFIG_SYSTEM_CDCACM in those two defconfigs to keep
that step.
Assisted-by: Claude:claude-sonnet-5
Signed-off-by: wangjianyu3 <wangjianyu3@xiaomi.com>
Adds a PWM lower-half using the eCAP modules in APWM mode as single-channel
generators rather than capture units.
start() reprograms the time base only when the frequency changes, so a
duty-only update does not stop or zero a live counter.
t3-gem-o1 registers /dev/ecap1 and /dev/ecap2; output pad selection is left to
the board, as the candidates collide with I2C0.
Verified on t3-gem-o1: examples/pwm runs a 1 kHz, 50% duty train on both
instances and accepts a duty-only change (25% then 75%). The output pins have
not been measured on copper, as no pad is assigned to them on this board.
Assisted-by: Claude Code:claude-opus-4-8
Signed-off-by: Ulaş Sertan Kemeç <sertan.usk@gmail.com>
Moves EPWM initialization from am67_bringup.c to am67_pwm.c. Initialization
now requires only a function call in bringup.c.
Nxstyle checked, builds same.
Signed-off-by: Ulaş Sertan Kemeç <sertan.usk@gmail.com>
Adds a PWM lower-half for EPWM0 and EPWM1, covering both output channels of
each. The CTRL_MMR EPWM clock enables are unlocked once during board bring-up.
t3-gem-o1 registers /dev/pwm0 and /dev/pwm1 with PWM_NCHANNELS=2.
Verified on t3-gem-o1: all four outputs (EPWM0 A+B, EPWM1 A+B) drive physical
pins, jumpered into a Linux GPIO input -- 50% and 20% duty read back at the
expected sample ratios, and gpiomon timed a 50 Hz half-period at 9.998-10.002
ms. examples/pwm starts and stops a 1 kHz train cleanly.
Assisted-by: Claude Code:claude-fable-5
Signed-off-by: Ulaş Sertan Kemeç <sertan.usk@gmail.com>
Record the WKUP_I2C0 master in the board's Peripheral Support list.
Assisted-by: Claude Code:claude-opus-5
Signed-off-by: Ulaş Sertan Kemeç <sertan.usk@gmail.com>
Adds an I2C master driver for the AM67 I2C instances, completing transfers on
ARDY as the K3 controller signals.
Bring-up is deferred to the first transfer, because the Linux Device Manager
enables the I2C clocks late and touching the bus during early board init is not
safe here. The last reference drop clears the flag so the next transfer
re-initialises the hardware.
t3-gem-o1 registers WKUP_I2C0 as /dev/i2c2.
Verified on t3-gem-o1: i2c dev finds 0x30, 0x40, 0x51 and 0x68, the RTC at
0x68 reads a ticking BCD seconds register, repeated reads are consistent, and
NACK recovery returns the bus to a usable state.
Assisted-by: Claude Code:claude-fable-5
Assisted-by: Claude Code:claude-opus-4-8
Signed-off-by: Ulaş Sertan Kemeç <sertan.usk@gmail.com>
If CONFIG_ARM_MPU and CONFIG_STM32_ICACHE are set, this will configure an
MPU region marking the OTP flash as non-cacheable. This prevents hard faults
when accessing the 4K OTP region from software.
Signed-off-by: Darryl Ring <darryl@bluerobotics.ca>
Add a Peripheral Support section to the board page listing the GPIO and
MCU_MCSPI0 drivers, and replace the "UART console only" warning on both
the chip and board pages -- it no longer describes the port. The
replacement states what actually constrains the port: NuttX runs on the
R5F under RemoteProc and depends on the bootloader or Linux Device
Manager having powered and clocked the peripherals, because there is no
TISCI client yet.
Assisted-by: Claude Code:claude-opus-5
Signed-off-by: Ulaş Sertan Kemeç <sertan.usk@gmail.com>
Adds the AM67 GPIO lower half and a polled MCU_MCSPI0 master driver, with the
pad configuration both need. The K3 instance is not the OMAP2 layout: an HL
header block precedes the functional registers.
Chip select is released only after CHSTAT.EOT, since a high SCLK otherwise
drops it mid-word and truncates the write, and CHCTRL.EN stays asserted between
transfers.
t3-gem-o1 registers /dev/spi0 for its ICM-20948 (CS3) and LPS22DF (CS1), and
raises NSH_MAXARGUMENTS to 16 so the spi tool can address a device.
Verified on t3-gem-o1: WHO_AM_I reads 0xEA on CS3 and 0xB4 on CS1, and the
ICM-20948 streams continuous accelerometer samples over the bus.
Co-authored-by: Ulaş Sertan Kemeç <sertan.usk@gmail.com>
Assisted-by: Cursor
Assisted-by: Claude Code:claude-opus-4-8
Signed-off-by: Ulaş Sertan Kemeç <sertan.usk@gmail.com>
The mcuboot-loader image overflows its flash region once the FAT deferred-delete change is applied. Long filename support is not needed by the bootloader, which boots from flash areas and never opens FAT files by long name, so disable CONFIG_FAT_LFN to reclaim the space while keeping short filename support intact.
Signed-off-by: Arnav Sharma <2006arnavsharma@gmail.com>
