3c3afd04bd
Arming a pin as a light-sleep wake source destroyed whatever it was
configured as, permanently.
esp_pm_gpio_wakeup_prepare() has to reconfigure each masked pin to plain
INPUT and hand it to gpio_wakeup_enable(), because the wakeup path only
supports level triggering. It then never put anything back. A pin that
was also a normal peripheral interrupt -- a sensor's data-ready line, say
-- came out of the first light sleep with its trigger mode gone and never
interrupted again. Nothing failed loudly; the device just went silent.
Fixed generically rather than per-board:
- esp_configgpio() now remembers the last attr applied to each pin, and
a new esp_getconfiggpio() hands it back. This is what lets the PM
code restore a pin without having to know what the pin is for.
- esp_pm_gpio_wakeup_prepare() saves each masked pin's attr before
overwriting it, and a new esp_pm_gpio_wakeup_restore() puts it back
as soon as esp_pm_light_sleep_start() returns.
Tied to the physical sleep/wake cycle deliberately, not to PM state
transitions. An earlier attempt used a board-level pm_register()/notify()
callback and never fired at all, because the board sits in PM_STANDBY
without transitioning back to PM_NORMAL -- there is no state change to
hang the restore on. The return from esp_pm_light_sleep_start() is the
one event that always happens exactly once per sleep.
Assisted-by: Claude:claude-opus-5
Signed-off-by: Felipe Moura <moura.fmo@gmail.com>
|
||
|---|---|---|
| .github | ||
| arch | ||
| audio | ||
| binfmt | ||
| boards | ||
| cmake | ||
| crypto | ||
| Documentation | ||
| drivers | ||
| dummy | ||
| fs | ||
| graphics | ||
| include | ||
| libs | ||
| mm | ||
| net | ||
| openamp | ||
| pass1 | ||
| sched | ||
| syscall | ||
| tools | ||
| video | ||
| wireless | ||
| .asf.yaml | ||
| .codespell-ignore-lines | ||
| .codespellrc | ||
| .editorconfig | ||
| .gitignore | ||
| .gitmessage | ||
| .pre-commit-config.yaml | ||
| .yamllint | ||
| AUTHORS | ||
| CMakeLists.txt | ||
| CONTRIBUTING.md | ||
| INVIOLABLES.md | ||
| Kconfig | ||
| LICENSE | ||
| Makefile | ||
| NOTICE | ||
| README.md | ||
| ReleaseNotes | ||
Apache NuttX is a real-time operating system (RTOS) with an emphasis on standards compliance and small footprint. Scalable from 8-bit to 64-bit microcontroller environments, the primary governing standards in NuttX are POSIX and ANSI standards. Additional standard APIs from Unix and other common RTOSs (such as VxWorks) are adopted for functionality not available under these standards, or for functionality that is not appropriate for deeply-embedded environments (such as fork()).
For brevity, many parts of the documentation will refer to Apache NuttX as simply NuttX.
Getting Started
First time on NuttX? Read the Getting Started guide! If you don't have a board available, NuttX has its own simulator that you can run on terminal.
Documentation
You can find the current NuttX documentation on the Documentation Page.
Alternatively, you can build the documentation yourself by following the Documentation Build Instructions.
The old NuttX documentation is still available in the Apache wiki.
Supported Boards
NuttX supports a wide variety of platforms. See the full list on the Supported Platforms page.
Contributing
If you wish to contribute to the NuttX project, read the Contributing guidelines for information on Git usage, coding standard, workflow and the NuttX principles.
License
The code in this repository is under either the Apache 2 license, or a license compatible with the Apache 2 license. See the License Page for more information.