- The frequency step was truncated to 61 Hz, while it is FXOSC/(2**19),
about 61.035 Hz. The error puts a 915 MHz channel more than 500 kHz away
from the requested frequency, outside its own bandwidth.
- The low or high frequency front end was left at its reset value, so a board
wired for 868 or 915 MHz neither transmitted nor received.
- sx127x_rx_watchdog() is only used by the FSK and OOK path but was compiled
whenever receive support was on, so a LoRa only configuration failed to
build with -Werror. nrf52840-dk:sx127x is such a configuration.
Adds the sync word, the default bandwidth and the default spreading factor as
configuration options, all defaulting to the previous behaviour, and a page
for the driver under components/drivers.
Assisted-by: Claude Code 4.8
Signed-off-by: Jorge Guzman <jorge.gzm@gmail.com>
Character driver for the Semtech SX1301, the baseband processor of a LoRaWAN
gateway, and the two SX125x radios it drives. Received packets come from
read(), downlinks go to write(), and the channel plan, the start and the stop
are ioctls.
The interface is device independent, in nuttx/wireless/lpwan/lora_gw.h with
the commands in the common WLIOC_GW_* space, so another concentrator driver
can implement it and the same application drive it.
Adds a lorawan_gw configuration for the Nucleo F746ZG with a shield of the
LRWAN_GS_HF1 family. Off by default (LPWAN_SX1301).
Assisted-by: Claude Code 4.8
Signed-off-by: Jorge Guzman <jorge.gzm@gmail.com>
Permissions (Part 2)
Description:
In kernel builds, any unprivileged process running on the NuttX
device can open /dev/efuse and attempt to read/write fuse content.
Reading the fuses may provide valuable information to an attacker
controlling the user process. The write operation, in extreme cases
where the fuse blocks are not locked, may brick the device.
DISCLAIMER: I tried to be strict with the settings, better to relax them
later if it's needed.
This is part of https://github.com/apache/nuttx/issues/19410
See https://github.com/apache/nuttx/issues/19410
Compiles ok.
Signed-off-by: Catalin Visinescu <catalin_visinescu@yahoo.com>
Long long support is now unconditional in printf/scanf and related
helpers. Remove the Kconfig option, the conditional compilation in
libvsprintf/libvscanf/ultoa_invert, the build-time #error in the
rn2xx3 driver, and clean up CONFIG_LIBC_LONG_LONG entries from all
board defconfigs.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
debug.h is a NuttX-specific, non-POSIX header. Placing it in the
top-level include/ directory creates naming conflicts with external
projects that define their own debug.h.
This commit moves the canonical header to include/nuttx/debug.h,
following the NuttX convention for non-POSIX/non-standard headers,
and updates all in-tree references.
A backward-compatibility shim is left at include/debug.h that
emits a deprecation #warning and re-includes <nuttx/debug.h>,
allowing out-of-tree code to continue building while migrating.
Signed-off-by: Piyush Patle <piyushpatle228@gmail.com>
Increase default TX power from 14 to 17 dBm and enable CRC
by default to improve link reliability and data integrity.
Signed-off-by: Arjav Patel <arjav1528@gmail.com>
This commit adds support to fix RX timeout for SX127x, it is done
leaving the RX mode, entering in stanby mode and returning to RX
mode. It is enough to fix the AFC and get communication working
again.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
This commit moves sx127x Kconfig to lpwan/sx127x/ to follow the
same logic used by sx126x and adds the configuration to support
different bitrate (the default 4800 is fine tuned for LORA).
Signed-off-by: Alan C. Assis <acassis@gmail.com>
Nuttx currently has 2 types of sleep interfaces:
1. Signal-scheduled sleep: nxsig_sleep() / nxsig_usleep() / nxsig_nanosleep()
Weaknesses:
a. Signal-dependent: The signal-scheduled sleep method is bound to the signal framework, while some driver sleep operations do not depend on signals.
b. Timespec conversion: Signal-scheduled sleep involves timespec conversion, which has a significant impact on performance.
2. Busy sleep: up_mdelay() / up_udelay()
Weaknesses:
a. Does not actively trigger scheduling, occupy the CPU loading.
3. New interfaces: Scheduled sleep: nxsched_sleep() / nxsched_usleep() / nxsched_msleep() / nxsched_ticksleep()
Strengths:
a. Does not depend on the signal framework.
b. Tick-based, without additional computational overhead.
Currently, the Nuttx driver framework extensively uses nxsig_* interfaces. However, the driver does not need to rely on signals or timespec conversion.
Therefore, a new set of APIs is added to reduce dependencies on other modules.
(This PR also aims to make signals optional, further reducing the code size of Nuttx.)
Signed-off-by: chao an <anchao.archer@bytedance.com>
This commit resolves issue #16009, where a sync word of less than 64
bytes was printed as 0-padded hex. 0-padding is invalid for the RN2xx3
modules, so now it has been removed.
Signed-off-by: Matteo Golin <matteo.golin@gmail.com>
radio transceivers. This initial support includes transmit and receive
functionality and configuration and reading of radio parameters like
frequency and bandwidth.
Signed-off-by: Matteo Golin <matteo.golin@gmail.com>
[Experimental]
This adds a driver for the SX126x (SX1261 and SX1262) LoRa chips.
All functions and definitions are coming directly from the DS SX1261-2 V2.1 datasheet.
Signed-off-by: Kevin Witteveen (MartiniMarter) <kevinwit1999@gmail.com>
Most tools used for compliance and SBOM generation use SPDX identifiers
This change brings us a step closer to an easy SBOM generation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
1. Update all CMakeLists.txt to adapt to new layout
2. Fix cmake build break
3. Update all new file license
4. Fully compatible with current compilation environment(use configure.sh or cmake as you choose)
------------------
How to test
From within nuttx/. Configure:
cmake -B build -DBOARD_CONFIG=sim/nsh -GNinja
cmake -B build -DBOARD_CONFIG=sim:nsh -GNinja
cmake -B build -DBOARD_CONFIG=sabre-6quad/smp -GNinja
cmake -B build -DBOARD_CONFIG=lm3s6965-ek/qemu-flat -GNinja
(or full path in custom board) :
cmake -B build -DBOARD_CONFIG=$PWD/boards/sim/sim/sim/configs/nsh -GNinja
This uses ninja generator (install with sudo apt install ninja-build). To build:
$ cmake --build build
menuconfig:
$ cmake --build build -t menuconfig
--------------------------
2. cmake/build: reformat the cmake style by cmake-format
https://github.com/cheshirekow/cmake_format
$ pip install cmakelang
$ for i in `find -name CMakeLists.txt`;do cmake-format $i -o $i;done
$ for i in `find -name *\.cmake`;do cmake-format $i -o $i;done
Co-authored-by: Matias N <matias@protobits.dev>
Signed-off-by: chao an <anchao@xiaomi.com>
since mmap may exist in block_operations, but truncate may not,
moving mmap beforee truncate could make three struct more compatible
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
- Add mmap into file_operations and remove it from ioctl definitions.
- Add mm_map structure definitions to support future unmapping
- Modify all drivers to initialize the operations struct accordingly
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
- Add truncate into file_operations
- Move truncate to be common for mountpt_operations and file_operations
- Modify all drivers to initialize the operations struct accordingly
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
In the past, header file paths were generated by the incdir command
Now they are generated by concatenating environment variables
In this way, when executing makefile, no shell command will be executed,
it will improve the speed of executing makfile
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
1.Don't check the return value of nxsem_init or nxmutex_init
2.Fix some style issue
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
lpc2148_spi1.c:142:24: warning: initialization of 'uint32_t (*)(struct spi_dev_s *, uint32_t)' {aka 'unsigned int (*)(struct spi_dev_s *, unsigned int)'} from incompatible pointer type 'uint16_t (*)(struct spi_dev_s *, uint16_t)' {aka 'short unsigned int (*)(struct spi_dev_s *, short unsigned int)'} [-Wincompatible-pointer-types]
142 | .send = spi_send,
| ^~~~~~~~
lpc2148_spi1.c:142:24: note: (near initialization for 'g_spiops.send')
In file included from ieee802154/mac802154_bind.c:49:
ieee802154/mac802154_internal.h: In function 'mac802154_setdevmode':
ieee802154/mac802154_internal.h:788:42: warning: converting a packed 'enum ieee802154_devmode_e' pointer (alignment 1) to a 'const union ieee802154_attr_u' pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
788 | (FAR const union ieee802154_attr_u *)&mode);
| ^~~~~~~~~~~~~~~~~
chip/stm32_hciuart.c: In function 'hciuart_read':
chip/stm32_hciuart.c:2104:30: warning: statement with no effect [-Wunused-value]
2104 | ntotal == (ssize_t)ret;
| ~~~~~~~^~~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c: In function 'bcmf_wl_auth_event_handler':
wireless/ieee80211/bcm43xxx/bcmf_driver.c:579:23: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
579 | type = bcmf_getle32(&event->type);
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c:580:25: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
580 | status = bcmf_getle32(&event->status);
| ^~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c: In function 'bcmf_wl_scan_event_handler':
wireless/ieee80211/bcm43xxx/bcmf_driver.c:619:25: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
619 | status = bcmf_getle32(&event->status);
| ^~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_driver.c:620:35: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
620 | escan_result_len = bcmf_getle32(&event->len);
| ^~~~~~~~~~~
wireless/ieee80211/bcm43xxx/bcmf_bdc.c: In function 'bcmf_bdc_process_event_frame':
wireless/ieee80211/bcm43xxx/bcmf_bdc.c:166:27: warning: taking address of packed member of 'struct bcmf_event_s' may result in an unaligned pointer value [-Waddress-of-packed-member]
166 | event_id = bcmf_getle32(&event_msg->event.type);
| ^~~~~~~~~~~~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c: In function 'sdio_io_rw_direct':
wireless/ieee80211/bcm43xxx/mmc_sdio.c:157:3: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
157 | ret = SDIO_RECVR5(dev, SD_ACMD52, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c: In function 'sdio_io_rw_extended':
wireless/ieee80211/bcm43xxx/mmc_sdio.c:239:11: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
239 | ret = SDIO_RECVR5(dev, SD_ACMD53, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:244:11: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
244 | ret = SDIO_RECVR5(dev, SD_ACMD53, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:257:7: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
257 | ret = SDIO_RECVR5(dev, SD_ACMD53, (uint32_t *)&resp);
| ^~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:265:3: warning: converting a packed 'struct sdio_resp_R5' pointer (alignment 1) to a 'uint32_t' {aka 'unsigned int'} pointer (alignment 4) may result in an unaligned pointer value [-Waddress-of-packed-member]
265 | SDIO_RECVR1(dev, SD_ACMD52ABRT, (uint32_t *)&resp);
| ^~~~~~~~~~~
wireless/ieee80211/bcm43xxx/mmc_sdio.c:79:28: note: defined here
79 | begin_packed_struct struct sdio_resp_R5
| ^~~~~~~~~~~~
chip/stm32_adc.c: In function 'adc_reset':
chip/stm32_adc.c:2860:7: warning: unused variable 'ret' [-Wunused-variable]
2860 | int ret;
| ^~~
chip/stm32_adc.c: In function 'adc_shutdown':
chip/stm32_adc.c:3044:7: warning: unused variable 'ret' [-Wunused-variable]
3044 | int ret;
| ^~~
chip/stm32_i2c.c:722:12: warning: 'stm32_i2c_sem_wait_noncancelable' defined but not used [-Wunused-function]
722 | static int stm32_i2c_sem_wait_noncancelable(FAR struct i2c_master_s *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
wireless/gs2200m.c: In function 'gs2200m_read':
wireless/gs2200m.c:727:20: warning: passing argument 1 of 'nxsem_wait' from incompatible pointer type [-Wincompatible-pointer-types]
727 | ret = nxsem_wait(dev);
| ^~~
| |
| struct gs2200m_dev_s *
.config:1207:warning: symbol value '' invalid for TESTING_OSTEST_FPUSIZE
platform/audio/cxd56_audio_analog.c:69:13: warning: inline function 'cxd56_audio_clock_is_enabled' declared but never defined
69 | inline bool cxd56_audio_clock_is_enabled(void);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
platform/audio/cxd56_audio_analog.c:68:13: warning: inline function 'cxd56_audio_clock_disable' declared but never defined
68 | inline void cxd56_audio_clock_disable(void);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
platform/audio/cxd56_audio_analog.c:67:13: warning: inline function 'cxd56_audio_clock_enable' declared but never defined
67 | inline void cxd56_audio_clock_enable(uint32_t clk, uint32_t div);
| ^~~~~~~~~~~~~~~~~~~~~~~~
chip/stm32_adc.c: In function 'adc_reset':
chip/stm32_adc.c:1348:7: warning: unused variable 'ret' [-Wunused-variable]
1348 | int ret;
| ^~~
chip/stm32_adc.c: In function 'adc_shutdown':
chip/stm32_adc.c:1496:7: warning: unused variable 'ret' [-Wunused-variable]
1496 | int ret;
| ^~~
chip/stm32_i2c.c:729:12: warning: 'stm32_i2c_sem_wait_uninterruptble' defined but not used [-Wunused-function]
729 | static int stm32_i2c_sem_wait_uninterruptble(FAR struct i2c_master_s *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
wireless/lpwan/sx127x/sx127x.c:147:52: warning: missing terminating ' character
147 | # warning OOK support is not complete, RX+TX doesn't work yet!
| ^
str71_spi.c:435:24: warning: initialization of 'uint32_t (*)(struct spi_dev_s *, uint32_t)' {aka 'unsigned int (*)(struct spi_dev_s *, unsigned int)'} from incompatible pointer type
'uint16_t (*)(struct spi_dev_s *, uint16_t)' {aka 'short unsigned int (*)(struct spi_dev_s *, short unsigned int)'} [-Wincompatible-pointer-types]
435 | .send = spi_send,
| ^~~~~~~~
str71_spi.c:435:24: note: (near initialization for 'g_spiops.send')
chip/pic32mx-lowconsole.c:147:24: warning: 'pic32mx_getreg' defined but not used [-Wunused-function]
static inline uint32_t pic32mx_getreg(uintptr_t uart_base,
^
chip/pic32mx-gpio.c:113:20: warning: 'pic32mx_value' defined but not used [-Wunused-function]
static inline bool pic32mx_value(uint16_t pinset)
^
chip/pic32mz-gpio.c:124:20: warning: 'pic32mz_value' defined but not used [-Wunused-function]
static inline bool pic32mz_value(pinset_t pinset)
^
chip/pic32mx-usbdev.c:3065:1: warning: 'pic32mx_epreserved' defined but not used [-Wunused-function]
pic32mx_epreserved(struct pic32mx_usbdev_s *priv, int epno)
^
mmcsd/mmcsd_spi.c: In function 'mmcsd_mediachanged':
mmcsd/mmcsd_spi.c:1938:7: warning: 'return' with a value, in function returning void
return ret;
^
In file included from partition/fs_partition.c:42:0:
partition/partition.h:66:19: warning: 'read_partition_block' defined but not used [-Wunused-function]
static inline int read_partition_block(FAR struct partition_state_s *state,
^
local/local_netpoll.c: In function 'local_pollsetup':
local/local_netpoll.c:305:1: warning: label 'pollerr' defined but not used [-Wunused-label]
pollerr:
^~~~~~~
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: If3ea8f32b878aa218072130f7c3018f0d3c1aca5
This reverts commit b9ace36fcc.
This change was added by PR 625 but has a serious logic flaw. It removes all occurrences of INCDIROPT and replaces it with a definition in tools/Config.mk:
else ifeq ($(WINTOOL),y)
DEFINE = "$(TOPDIR)/tools/define.sh"
INCDIR = "$(TOPDIR)/tools/incdir.sh" -w
This logic flaw is the Config.mk is included in all Make.defs files BEFORE WINTOOL is defined. As a result, the definition is wrong in many places when building under Cygwin with a Windows native toolchain.
