The headers test CONFIG_STM32H5_* names that no Kconfig defines (the
STM32H5xXXX families, FLASHEN, OTFDEC1EN, DCACHE, STM32H2X/H3X/H7X), so
those branches are dead code. Use the common CONFIG_STM32_* symbols.
Fix what this exposes: derive the SRAM2/SRAM3 bases from the family SRAM
sizes, since the boot ECC init would otherwise write past the end of RAM
on smaller parts, correct the H52x/H53x SPI count to SPI1-4 and drop the
STM32_STM32H5X3XX select, which names no symbol.
Signed-off-by: raiden00pl <raiden00@railab.me>
Assisted-by: Claude Code
Correct the number of GPIO ports (STM32_NPORTS) from 8 to 9 and include
GPIOI in the g_gpiobase array. Also fix the comparison that would
prevent the GPIOI clock from being enabled (this is really a no-op,
though).
Signed-off-by: Darryl Ring <darryl@bluerobotics.com>
BREAKING CHANGE: STM32H5 Kconfig symbols were renamed from CONFIG_STM32H5_* to CONFIG_STM32_*.
Out-of-tree code must update defconfigs and Kconfig references to the new CONFIG_STM32_* names.
The custom clock option is a special breaking case that does not follow the family-to-common pattern:
CONFIG_ARCH_BOARD_STM32H5_CUSTOM_CLOCKCONFIG was renamed to CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG.
Signed-off-by: raiden00pl <raiden00@railab.me>
BREAKING CHANGE: STM32H5 non-standard hardware definition macros
(IRQ, peripheral-count, SRAM and related) were renamed to the common
STM32_* prefix. Out-of-tree code must update the affected references.
Signed-off-by: raiden00pl <raiden00@railab.me>
Rename STM32_IRQ_NEXTINT to STM32_IRQ_NEXTINTS across all stm32
variants.
In stm32_dumpnvic() dynamically print NVIC enable and priority
registers based on STM32_IRQ_NEXTINTS.
Use PRIx32 format specifier instead of 'x' (since uint32_t on arm is
actually a long unsigned int).
Simplify if/else chain in stm32_irqinfo() to determine irq reg/bit.
There's no stm32_irqinfo.c; remove mention in stm32f0l0g0/Make.defs.
Signed-off-by Peter Barada <peter.barada@gmail.com>
copied over files, not modified properly yet
Squashing lots of define errors to get ethernet.c working
quick path rename
Fix STM32_EMAC_BASE (and ICACHE/DCACHE Bases). Enable ETH, ETHTX, and ETHRX with CONFIG_STM32H5_ETHMAC (like H7 does).
Fixed stm32_get_uniqueid
Previously, an exception occurred as a result of calling this function. The problem turned out to be this line: uniqueid[i] = *((uint8_t *)(STM32_SYSMEM_UID) + i);. Dereferencing a 32-bit register as a 8-bit register seemed to be causing this issue. I think this function is better anyway, fewer register accesses and loop iterations.
Turn on SBS peripheral when using Ethernet
The SBS peripheral is required to be turned on because the ETH_SEL_PHY bits need to be set. Without turning this on, RMII mode is not possible. MII may not work either.
Style Updates
Most tools used for compliance and SBOM generation use SPDX identifiers
This change brings us a step closer to an easy SBOM generation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Created stm32h5 directory to add support for the H5 chip, and used a Nucleo-H563ZI dev board during development. The goal was to get a working nutshell through the STLink connector on the board.
Remove board/docs changes for PR update.
Squash commits into one for PR guideline conformity.
trying to fix build issues
Fix format from review
