Enable the OTG FS host on the Linum board so an external USB HID keyboard
can be used: configure the USB VBUS, power-switch and over-current GPIOs
at board bring-up (the power switch on PI12 is active low) and start the
USB host from stm32_bringup() through stm32_usbhost_initialize().
Add the lvglterm_kbda configuration - the LVGL terminal driven by a USB
HID keyboard on /dev/kbda - with the microSD card enabled alongside the
USB host. They coexist once CONFIG_MMCSD_MMCSUPPORT is left disabled, so
an SD card is not probed as an MMC device.
Also switch esp32s3-m5-cardputer:lvglterm to the renamed matrix-keyboard
input option (EXAMPLES_LVGLTERM_INPUT_KBD_MATRIX) to match the reworked
lvglterm example Kconfig.
Update the documentation accordingly: the LVGL Terminal example page for
the three-way input choice (touch, matrix, USB HID) with cursor-key
scrolling and per-variant configuration plus a photo of the USB variant
running on the Linum, the lvglterm_kbda entry on the Linum board page,
and the matrix-keyboard variant name on the M5Stack Cardputer board page.
Signed-off-by: Jorge Guzman <jorge.gzm@gmail.com>
Add the 56-key matrix keyboard driver for the M5Stack Cardputer. The keys
form an 8x7 matrix behind a 74HC138 3-to-8 demultiplexer; the driver scans it
on the low-priority work queue and registers a keyboard device at /dev/kbd0,
reporting ASCII codes with SHIFT/CTRL and Fn (cursor) handling.
Add an "lvglterm" configuration that runs the on-screen NuttShell terminal
(apps/examples/lvglterm, physical-keyboard input variant) on the ST7789
display: the shell output is rendered in an LVGL text area and the keyboard
feeds the input. Wi-Fi is included so the on-screen shell can associate with
an access point using wapi.
Signed-off-by: Jorge Guzman <jorge.gzm@gmail.com>
This port adds support for the M5Stack Cardputer (M5Stamp S3 /
ESP32-S3FN8, dual Xtensa LX7 @ 240 MHz, 8 MB flash, no PSRAM).
It reuses the common ESP32-S3 board helpers and ships these
configurations:
- nsh: NuttShell over the USB-Serial-JTAG console
- sdcard: microSD card on SPI3 (FAT)
- fb: ST7789 240x135 display exposed as a framebuffer
- wifi: Wi-Fi station
- softap: Wi-Fi SoftAP with DHCP server
- lvgl: LVGL graphics on the ST7789 (lvgldemo)
Signed-off-by: Jorge Guzman <jorge.gzm@gmail.com>
* Initial experimental / work in progress implementation.
* New board name is esp32s3-ws-lcd128.
* Supports Kconfig delectable w/wo touch variants (lcd gpios difference).
* IMU QMI8658 bringups is put into esp32s3/common/src to share with other
boards. Pin defines are located at <board>include/board.h and referenced
with `#include <arch/board/board.h>`.
* Supported configurations: nsh, ostest, coremark, touch-lvgl, notouch-lvgl,
imu-qmi8658, watchdog.
* Does not have touch panel driver yet.
* Created board documentation. Added sphinx inline cross-references.
* TODO: Fix SPI GC9A01A LCD pixel format colors.
* TODO: Create I2C CST816S touch panel driver.
Signed-off-by: Tomasz 'CeDeROM' CEDRO <tomek@cedro.info>
Updated the `rmt` defconfig description for the Espressif's SoCs.
Use the `irtest` testing app (instead of the deprecated `rmtchar`)
to test the RMT peripheral.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
Add board-level support for ES7210 4-ch ADC on lckfb-szpi-esp32s3:
- configs/es7210/defconfig: Board configuration with I2C0, I2S0,
ES7210 driver enabled. I2S pins: BCLK=14, DIN=12, MCLK=38, WS=13,
sample rate 48kHz.
- src/esp32s3_board_es7210.c: Board init registering ES7210 on I2C0
bus with I2S0 as audio transport
- src/esp32s3_bringup.c: Call ES7210 board init on startup; skip
generic I2S audio device registration on I2S0 when ES7210 is
enabled to avoid conflicting audio device on the same port
- src/esp32s3-szpi.h: ES7210 I2C address and device path defines
- src/Make.defs: Build integration for CONFIG_AUDIO_ES7210
Tested: 48kHz/2ch/16bit recording on ESP32-S3 (lckfb-szpi N16R8),
verified with nxrecorder and es7210_test.
Signed-off-by: wangjianyu3 <wangjianyu3@xiaomi.com>
Add UVC configuration for lckfb-szpi-esp32s3 board based on gc0308
camera config, with USB OTG and UVC gadget driver enabled in
standalone (non-composite) mode.
- defconfig: enable ESP32S3_OTG, USBUVC, UVC example app
- board doc: add uvc section with usage and host verification
Signed-off-by: wangjianyu3 <wangjianyu3@xiaomi.com>
Add a minimal GC0308 camera configuration based on nsh. Unlike the
full camera config, this only enables the GC0308 DVP camera driver
(I2C, PCA9557, LEDC, CAM, VIDEO) and camcap example, without ADB,
SDMMC, LCD, PSRAM or other peripherals.
Signed-off-by: wangjianyu3 <wangjianyu3@xiaomi.com>
Add camera configuration for lckfb-szpi-esp32s3 board with GC0308
sensor on DVP interface. Includes board-level camera initialization,
DVP GPIO pin mapping, and V4L2 video pipeline setup.
Signed-off-by: wangjianyu3 <wangjianyu3@xiaomi.com>
Add support for the QMI8658 6-axis IMU sensor (accelerometer + gyroscope)
on the lckfb-szpi-esp32s3 board.
Changes:
- New esp32s3_qmi8658.c driver initializes sensor on I2C0 at address 0x6A
- Registers uORB devices: /dev/uorb/sensor_accel0 and /dev/uorb/sensor_gyro0
- Adds esp32s3_qmi8658_initialize() function declaration to header
- Integrates with board bringup when CONFIG_SENSORS_QMI8658=y
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
Introduce EXT1 wakeup functionality to the ESP32-S3 power management
subsystem. With this feature, the ESP32-S3 can wake up from PM_STANDBY
or PM_SLEEP when one or more RTC GPIOs trigger the EXT1 condition.
Changes include:
- Added EXT1 wakeup configuration and preparation logic in rtc code.
- Integrated EXT1 handling in pmstandby() and pmsleep().
- New board-level Kconfig options under ESP32-S3 DevKit menu:
- CONFIG_PM_EXT1_WAKEUP: enable EXT1 wakeup support
- CONFIG_PM_EXT1_WAKEUP_RTC_GPIO<n>: select RTC GPIOs as wake sources
- CONFIG_PM_EXT1_WAKEUP_TRIGGER_MODE: choose wakeup on HIGH or LOW level
- Fixing Kconfig style
- Fixing comments standard
- Adding PM documentation for esp32s3-devkit
Impact:
- No build impact unless CONFIG_PM_EXT1_WAKEUP is enabled.
- When enabled, ESP32-S3 can wake from low-power states via RTC GPIOs.
- No new public API introduced; controlled via board Kconfig.
Tested on ESP32-S3 DevKit:
- Configured GPIO4 and GPIO5 as EXT1 wake sources.
- Verified wakeup from light sleep and deep sleep on external signals.
- Wakeup reason correctly reported as EXT1.
Signed-off-by: Thiago Finelon <thiago.sfinelon@gmail.com>
- Added esp32s3_board_spislavedev.c with board-level SPI slave logic
- Added esp32s3_board_spislavedev.h public header in common/include
- Updated Make.defs to include the new source when CONFIG_SPI_SLAVE_DRIVER=y
- Adding spislv board config to esp32s3-devkit
- Adding documentation of esp32s3 devkit spi slv
- Fixing path include in esp32s3_board_spislavedev.c
- Fixing relative path in the header of esp32s3_board_spislavedev.h
- Removing neasted check in Make.defs, consistency reasons
This provides initial support for SPI slave device initialization
on ESP32-S3 boards, making the feature available under conditional
build configuration.
Signed-off-by: Thiago Finelon <thiago.sfinelon@gmail.com>
This updated the command used for running the openocd-esp32 for
all the supported Espressif's SoCs. It enables using SW-defined
breakpoints.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
Change the ESP32S3-WROOM-2-N16R8V to ESP32S3-WROOM-1-N8R2.
Reason: not testing on 16MB but successfully tested smaller flash and PSRAM.
Also updated documentation on this defconfig.
Signed-off-by: Filipe Cavalcanti <filipe.cavalcanti@espressif.com>
