Fix 269 occurrences of duplicate "the" word typo found in 209 files
across source code, header files, and configuration.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
Previously, the ST7796 driver required the board to pass a struct
st7796_config_s at initialization time, carrying display resolution,
color depth, orientation (MADCTL), BGR flag, SPI frequency, and
initial rotation.
All of these are chip-level properties, not board wiring details.
This created an awkward split: board code computed MADCTL values,
selected BPP, and derived effective resolution depending on orientation
(knowledge that belongs exclusively in the generic driver).
This commit removes that split entirely, following the same pattern used
by the ST7789 driver in drivers/lcd/Kconfig. It also implements the
getpower/setpower interface for standard framebuffer power management.
What was changed (per file):
drivers/lcd/Kconfig:
- Added a full 'if LCD_ST7796' ... 'endif # LCD_ST7796' block containing
all chip-level configuration.
- Includes LCD_ST7796_XRES/YRES, LCD_ST7796_BPP, LCD_ST7796_FREQUENCY,
LCD_ST7796_SPIMODE, LCD_ST7796_BGR, LCD_ST7796_INVCOLOR,
and orientation/rotation choices.
drivers/lcd/st7796.c:
- Removed struct st7796_config_s from struct st7796_dev_s.
- Moved struct st7796_cmd_s from public header to Private Types.
- Added compile-time macros derived from Kconfig:
ST7796_XRES/YRES (swapped for landscape),
ST7796_MADCTL_BASE,
ST7796_SPIMODE,
ST7796_BYTESPP,
ST7796_COLORFMT.
- Implemented st7796_getpower() and st7796_setpower() using the
st7796_board_power() board callback.
- Registered power functions in st7796_fbinitialize() vtable.
- Updated st7796_init_display() to make INVON/INVOFF conditional on
CONFIG_LCD_ST7796_INVCOLOR.
- Simplified st7796_fbinitialize() signature to only take
'struct spi_dev_s *spi'.
include/nuttx/lcd/st7796.h:
- Removed legacy macros (ST7796_XRES_RAW, etc.) and configuration
structures.
- Updated st7796_fbinitialize() prototype.
- Added st7796_board_power() callback prototype.
- Removed private implementation details from the public header.
boards/arm/stm32h7/nucleo-h753zi/Kconfig:
- Removed chip-level menus (settings, orientation) now handled by the
generic driver.
- Retained only board-specific wiring concerns (pins and SPI bus).
boards/.../stm32_st7796.c:
- Removed g_st7796_config and associated board-side macros.
- Updated st7796_fbinitialize() call to the new signature.
- stm32_st7796_flush_fb() now queries effective resolution
via g_fb_vtable->getvideoinfo().
Verified on nucleo-h753zi:
Orientation: Landscape (480x320),
Rotation: 180 deg,
BGR: enabled,
INVCOLOR: disabled,
BPP: RGB565,
Frequency: 40 MHz.
Making INVCOLOR a Kconfig option (default n) fixes cases where panels
previously showed inverted colors due to hardcoded INVON.
Signed-off-by: vrmay23 <vmay.sweden@gmail.com>
Add support for ST7796 TFT LCD controller (320x480). The driver
implements the NuttX framebuffer interface for SPI-connected displays.
Features:
- SPI interface with CONFIG_SPI_CMDDATA for D/C pin control;
- RGB565 (16-bit) and RGB666 (18-bit) color formats;
- Runtime rotation support (0, 90, 180, 270 degrees) via MADCTL;
- Board-provided configuration via st7796_config_s structure;
- Partial screen update via updatearea for efficient rendering;
- Persistent swap buffer to avoid per-frame allocations;
- Proper ST7796S initialization sequence with documented timing;
The driver uses a board-provided configuration structure allowing
flexible setup of resolution, SPI frequency, color depth, and
initial MADCTL value without requiring Kconfig options in the
generic driver.
Architecture changes in this revision as per request:
- Moved internal register commands to .c file (private)
- Moved MADCTL bit definitions to .c file (private)
- Moved struct st7796_cmd_s to .c file (private)
- Converted MADCTL orientation macros to absolute values
- Moved CONFIG_SPI_CMDDATA error check to beginning of file
- Removed duplicated CONFIG_SPI_CMDDATA guards
- Public header contains only board configuration API
- Changed the Kconfig auto-select FB from 'select' to 'depends on'
Tested with LVGL graphics library on STM32H753ZI board (my own port).
Signed-off-by: Vinicius May <vmay.sweden@gmail.com>
Some display drivers, like ILI9341, support 3-wire 9-bit SPI. In
contrast to 4-wire 8-bit SPI, which uses dedicated CMD/DATA pin to
distinguish between CMD and DATA, 3-wire 9-bit SPI uses MSB of 9-bit
frame for this purpose.
Signed-off-by: Jiri Vlasak <jvlasak@elektroline.cz>
It is now possible to configure SPI delays for st7789 controller if
CONFIG_SPI_DELAY_CONTROL is set. Default values for SPI peripheral
may be too long or too short, therefore the display controller set
its own values as required. The default values in configuration
are taken from the reference manual, but it is possible they may
require tuning for different revisions or temperatures for
example.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
ST7789 fills the display with 0xffff color during its initialization.
This color may or may not be overwritten by a higher layer (framebuffer
or lcd driver for example). The color remains on the display until
application UI is started if not overwritten by the higher layer before.
This commit adds configuration option LCD_ST7789_DEFAULT_COLOR that
allows to set the default background color. This may avoid shining
display with, for example, white color for an extensive amount of time.
The default value is set to 0xffff previously hard-coded in the driver,
therefore current implementations will not notice the change.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Add configuration and driver support for the SSD1681 1.54 inch e-paper display,
including the necessary waveforms and settings for proper operation. This extends
the existing SSD1680 e-paper driver to accommodate the new display module.
The changes involve updates to the Kconfig file for additional configuration options,
modifications to the driver implementation in ssd1680.c to include SSD1681 specific
logic, and updates to the header file ssd1680.h to reflect the added support.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
3 wire interface for ST7789 LCD controller does not use CMD/DATA pin to
specify whether data or command is send but uses 9th bit of SPI transfer.
This commit adds support for 3 wire interface to ST7789 controller.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Support mirror display by X/Y axis, it's useful for
single portrait/landscape but need to mirror specific direction.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
In order to support multiple LCD instances per board, add a pointer from
lcd_planeinfo_s to the lcd_dev_s which it belongs to. Also enhance the
putrun, getrun, putarea and getarea methods to pass through the
lcd_dev_s pointer to the respective device driver.
Port all LCD device drivers to this lcd_planeinfo_s extension.
Enhance SSD1306 driver to support multiple LCDs.
Signed-off-by: Michael Jung <michael.jung@secore.ly>
1.Expose the notification through fb_vtable_s::updatearea
2.Incorporate old nx_notify_rectangle into the new updatearea callback
3.Migrate the calle of nx_notify_rectangle to fb_vtable_s::updatearea
Change-Id: Ia3d1f73e8757b2d381586d76ec6adc16c810018d
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
since graphics/Kconfig already do the similar thing
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ib2c1955a6b027cfa4e83c3b81ddfb505902dd85d
