The CH422G offers eight bi-directional pins, IO0-IO7, and four open-drain
outputs, OC0-OC3. It appears on boards that have run out of usable GPIOs
once a parallel RGB panel has taken its share, the Waveshare
ESP32-S3-Touch-LCD-7 among them, where it holds the panel and touch
controller in and out of reset and switches the backlight.
Two things about the device do not fit the shape a register-per-address
I2C driver usually takes, and both are handled here rather than pushed on
to board logic:
- A register is selected by the I2C address the transfer is addressed
to, not by a register address written ahead of the data. Each access
carries a single byte to one of four addresses.
- None of the write-only registers can be read back, so the driver
keeps a shadow copy of each and updates it in step with the device.
IO0-IO7 have no individual direction control; one bit of the system
parameter register drives the whole group. The driver records the
direction asked of each pin and puts the group in output mode once at
least one of them is an output, which is what a board that drives some of
the pins would expect. Reading a pin of a group held in output mode
reports the value last written, because the hardware cannot report the
level, and that is documented rather than hidden.
The four open-drain outputs are presented as pins 8-11 of the same
ioexpander_dev_s so that one instance covers the chip, which means
CONFIG_IOEXPANDER_NPINS must be at least 12.
Builds clean with no new warnings on esp32s3-touch-lcd7:usbnsh and passes
nxstyle.
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Assisted-by: Claude Code
Adds support for the PIO4IOE IO Expander, more specifically the PIO4IOE5V6408 version.
Assisted-by: Cursor IDE agents
Signed-off-by: Filipe Cavalcanti <filipe.cavalcanti@espressif.com>
This is an I2C driver for the Awinic AW9523B I/O expander. As well
as the supporting usual digital I/Os, this device features the
ability to drive LEDs directly, and can control the drive current
to each LED individually. The driver was derived from the PCA9555
driver, provides all the standard interfaces of an i/o expander
driver. It also features support for the special features of the
AW9523B through pin direction IOEXPANDER_DIRECTION_OUT_LED and
IOEXPANDER_OPTION_NONGENERIC with AW9523B_OPTION_* options.
The driver has a number of configurable features including interrupt
handling and a shadow register mode based on the PCA9555 driver,
plus new LED/dimming support.
Testing was done using an ESP32S3 host and I2C connection to the
Adafruit AW9523 breakout board.
Signed-off-by: Zik Saleeba <zik@zikzak.net>
Most tools used for compliance and SBOM generation use SPDX identifiers
This change brings us a step closer to an easy SBOM generation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
This commit adds basic support for iC-JX expander in SPI mode. The
expander is functional and supports both input and output pins. Further
expander functionalities (filtering, adc, interrupt support) are not
yet implemented.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit adds basic support for electrically isolated 8 bit expander.
The expander communicates with the MCU via SPI interface. Both single
and multiple pin read are supported.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit adds support for galvanic isolated ISO1H812G SPI expander.
Both single pin and multiple pin writes are supported.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This adds support for 16 bit io expander pcf8575. The driver is basically
the same as for pcf8574 however it is for 16 bits instead of 8 bits. Since
pcf8575 and pcf8574 can be both used on the same i2c bus the driver for
pcf8575 is implemented in a different file to reduce the code size
and complexity and to have less if statements in the driver.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
In the past, header file paths were generated by the incdir command
Now they are generated by concatenating environment variables
In this way, when executing makefile, no shell command will be executed,
it will improve the speed of executing makfile
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
Sebastien Lorquet has submitted the ICL and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
This reverts commit b9ace36fcc.
This change was added by PR 625 but has a serious logic flaw. It removes all occurrences of INCDIROPT and replaces it with a definition in tools/Config.mk:
else ifeq ($(WINTOOL),y)
DEFINE = "$(TOPDIR)/tools/define.sh"
INCDIR = "$(TOPDIR)/tools/incdir.sh" -w
This logic flaw is the Config.mk is included in all Make.defs files BEFORE WINTOOL is defined. As a result, the definition is wrong in many places when building under Cygwin with a Windows native toolchain.
-headers in nuttx/ioexpander to define the "generic" ioexpander framework
-files in drivers/ioexpander for the implementation of the NXP PCA9555 framework
-bindings in drivers/Kconfig and drivers/Makefile
From Sebastien Lorquet
