Aksal/nuttx
3
1
Fork 1
mirror of https://github.com/apache/nuttx.git synced 2026-09-02 15:12:59 +00:00
Code Issues Projects Releases Packages Wiki Activity Actions 3
nuttx/configs/same70-xplained/src/same70-xplained.h
Anthony Merlino 14fb37c995 Merged in antmerlino/nuttx/sixlowpan-mac802154 (pull request #526) 
ieee802154: Simplifies notify() and rxframe() calls to a single notify() call. dataind's and all other "notifs" are now "primitives" which aligns with standard terminology

* mac802154: Adds missing breaks from case statement

* sixlowpan: Fixes bad logic where ACK is not requested if address is not a broadcast

* ieee802154: Simplification of "notifs" and "datainds" to generic primitives passed via a single notify call to the layer above the MAC

* Directories.mk should reference CONFIG_WIRELESS instead of CONFIG_DRIVERS_WIRELESS

* xbee_netdev: Network must be locked when calling sixlowpan_input

* sixlowpan: Reassembly buffer can't be freed if provided by radio driver

* sixlowpan: Don't free IOB if there is an error processing it as the MAC will try to pass it along to another receiver

* ieee802154: Adds basic logging to ieee802154_primitive.c

* Minor fixes after rebase

* xbee: Adds AT query timeout to retry if XBee doesn't respond to request

* same70-xplained: Adds Xbee support. Makes mikroBus slot Kconfig 'choice'

* mac802154: Removes unused function declaration

* drivers/mrf24j40: Fixes compilation error using . operator rather than -> operator

* mac802154_device: Changes a few mac802154_primtive_free's to ieee802154_primitive_free() and changes notif to primitive in a couple places.

* mac802154: Adds promiscous mode logic to bypass parsing of incoming frames. MAC char device also checks for promiscous mode and passes whole frames including header and FCS to the application if promiscous mode is enabled.

* sixlowpan: Fixes logic to correctly check if packet is large enough to include header.  This would cause packets to be considered too small when they are sufficiently sized.

* sixlowpan: Fixes forwarding logic to use forwarding device rather than received device to look up destination link layer address

* net/ipforward: Fixes typo that caused build error when IP forwarding was enabled with CONFIG_NET_ICMPv6_NEIGHBOR enabled as well.

* configs/same70-xplained: Simple spelling fix

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2017-11-01 20:15:21 +00:00

675 lines
21 KiB
C
Raw Blame History

/************************************************************************************
* configs/same70-xplained/src/same70-xplained.h
*
* Copyright (C) 2015, 2017 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_SAME70_XPLAINED_SRC_SAME70_XPLAINED_H
#define __CONFIGS_SAME70_XPLAINED_SRC_SAME70_XPLAINED_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#include <stdint.h>
#include <stdbool.h>
#include <arch/irq.h>
#include <nuttx/irq.h>
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* Configuration ********************************************************************/
#define HAVE_HSMCI 1
#define HAVE_AUTOMOUNTER 1
#define HAVE_USB 1
#define HAVE_USBDEV 1
#define HAVE_USBMONITOR 1
#define HAVE_NETWORK 1
#define HAVE_MACADDR 1
#define HAVE_MTDCONFIG 1
#define HAVE_PROGMEM_CHARDEV 1
#define HAVE_I2CTOOL 1
#define HAVE_MRF24J40 1
#define HAVE_XBEE 1
/* HSMCI */
/* Can't support MMC/SD if the card interface is not enabled */
#if !defined(CONFIG_SAMV7_HSMCI0)
# undef HAVE_HSMCI
#endif
/* Can't support MMC/SD features if mountpoints are disabled */
#if defined(HAVE_HSMCI) && defined(CONFIG_DISABLE_MOUNTPOINT)
# warning Mountpoints disabled. No MMC/SD support
# undef HAVE_HSMCI
#endif
/* We need PIO interrupts on GPIOC to support card detect interrupts */
#if defined(HAVE_HSMCI) && !defined(CONFIG_SAMV7_GPIOC_IRQ)
# warning PIOC interrupts not enabled. No MMC/SD support.
# undef HAVE_HSMCI
#endif
/* MMC/SD minor numbers */
#ifndef CONFIG_NSH_MMCSDMINOR
# define CONFIG_NSH_MMCSDMINOR 0
#endif
#ifndef CONFIG_NSH_MMCSDSLOTNO
# define CONFIG_NSH_MMCSDSLOTNO 0
#endif
#if CONFIG_NSH_MMCSDSLOTNO != 0
# error SAME70 has only one MMC/SD slot (CONFIG_NSH_MMCSDSLOTNO)
# undef CONFIG_NSH_MMCSDSLOTNO
# define CONFIG_NSH_MMCSDSLOTNO 0
#endif
#define HSMCI0_SLOTNO CONFIG_NSH_MMCSDSLOTNO
#define HSMCI0_MINOR CONFIG_NSH_MMCSDMINOR
/* Automounter. Currently only works with HSMCI. */
#if !defined(CONFIG_FS_AUTOMOUNTER) || !defined(HAVE_HSMCI)
# undef HAVE_AUTOMOUNTER
# undef CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT
#endif
#ifndef CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT
# undef HAVE_AUTOMOUNTER
#endif
#ifdef HAVE_AUTOMOUNTER
# ifdef CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT
/* HSMCI0 Automounter defaults */
# ifndef CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT_FSTYPE
# define CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT_FSTYPE "vfat"
# endif
# ifndef CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT_BLKDEV
# define CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT_BLKDEV "/dev/mmcds0"
# endif
# ifndef CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT_MOUNTPOINT
# define CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT_MOUNTPOINT "/mnt/sdcard0"
# endif
# ifndef CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT_DDELAY
# define CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT_DDELAY 1000
# endif
# ifndef CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT_UDELAY
# define CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT_UDELAY 2000
# endif
# endif /* CONFIG_SAME70XPLAINED_HSMCI0_AUTOMOUNT */
#endif /* HAVE_AUTOMOUNTER */
/* USB Device */
/* CONFIG_SAMV7_UDP and CONFIG_USBDEV must be defined, or there is no USB
* device.
*/
#if !defined(CONFIG_SAMV7_UDP) || !defined(CONFIG_USBDEV)
# undef HAVE_USB
# undef HAVE_USBDEV
#endif
/* Check if we should enable the USB monitor before starting NSH */
#ifndef HAVE_USBDEV
# undef CONFIG_USBDEV_TRACE
#endif
#if !defined(CONFIG_USBMONITOR) || !defined(CONFIG_USBDEV_TRACE)
# undef HAVE_USBMONITOR
#endif
/* Networking and AT24-based MTD config */
#if !defined(CONFIG_NET) || !defined(CONFIG_SAMV7_EMAC)
# undef HAVE_NETWORK
# undef HAVE_MACADDR
#endif
#if !defined(CONFIG_SAMV7_TWIHS0) || !defined(CONFIG_MTD_AT24XX)
# undef HAVE_MACADDR
# undef HAVE_MTDCONFIG
#endif
#if defined(CONFIG_NSH_NOMAC) || !defined(CONFIG_AT24XX_EXTENDED)
# undef HAVE_MACADDR
#endif
#if !defined(CONFIG_MTD_CONFIG)
# undef HAVE_MTDCONFIG
#endif
/* On-chip Programming Memory */
#if !defined(CONFIG_SAMV7_PROGMEM) || !defined(CONFIG_MTD_PROGMEM)
# undef HAVE_PROGMEM_CHARDEV
#endif
/* This is the on-chip progmem memroy driver minor number */
#define PROGMEM_MTD_MINOR 0
/* Do we need to register I2C drivers on behalf of the I2C tool? */
#if !defined(CONFIG_SYSTEM_I2CTOOL) || !defined(CONFIG_I2C_DRIVER)
# undef HAVE_I2CTOOL
#endif
/* procfs File System */
#ifdef CONFIG_FS_PROCFS
# ifdef CONFIG_NSH_PROC_MOUNTPOINT
# define SAME70_PROCFS_MOUNTPOINT CONFIG_NSH_PROC_MOUNTPOINT
# else
# define SAME70_PROCFS_MOUNTPOINT "/proc"
# endif
#endif
/* Check if the MRF24J40 is supported in this configuration */
#ifndef CONFIG_IEEE802154_MRF24J40
# undef HAVE_MRF24J40
#endif
#ifndef CONFIG_SAME70XPLAINED_CLICKSHIELD
# undef HAVE_MRF24J40
#endif
#if !defined(CONFIG_SAME70XPLAINED_MB1_BEE) && !defined(CONFIG_SAME70XPLAINED_MB2_BEE)
# undef HAVE_MRF24J40
#endif
#ifndef CONFIG_SAMV7_SPI0_MASTER
# undef HAVE_MRF24J40
#endif
#ifndef CONFIG_SAMV7_GPIOA_IRQ
# undef HAVE_MRF24J40
#endif
/* Check if the XBee is supported in this configuration */
#ifndef CONFIG_IEEE802154_XBEE
# undef HAVE_XBEE
#endif
#ifndef CONFIG_SAME70XPLAINED_CLICKSHIELD
# undef HAVE_XBEE
#endif
#if !defined(CONFIG_SAME70XPLAINED_MB1_XBEE) && !defined(CONFIG_SAME70XPLAINED_MB2_XBEE) && \
!defined(CONFIG_SAME70XPLAINED_MB3_XBEE)
# undef HAVE_XBEE
#endif
#ifndef CONFIG_SAMV7_SPI0_MASTER
# undef HAVE_XBEE
#endif
#ifndef CONFIG_SAMV7_GPIOA_IRQ
# undef HAVE_XBEE
#endif
/* SAME70-XPLD GPIO Pin Definitions *************************************************/
/* Ethernet MAC.
*
* KSZ8081RNACA Connections
* ------------------------
*
* ------ --------- ---------
* SAME70 SAME70 Ethernet
* Pin Function Functio
* ------ --------- ---------
* PD0 GTXCK REF_CLK
* PD1 GTXEN TXEN
* PD2 GTX0 TXD0
* PD3 GTX1 TXD1
* PD4 GRXDV CRS_DV
* PD5 GRX0 RXD0
* PD6 GRX1 RXD1
* PD7 GRXER RXER
* PD8 GMDC MDC
* PD9 GMDIO MDIO
* PA14 GPIO INTERRUPT
* PC10 GPIO RESET
* ------ --------- ---------
*/
#define GPIO_EMAC0_INT (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_CFG_DEGLITCH | \
GPIO_INT_FALLING | GPIO_PORT_PIOA | GPIO_PIN14)
#define GPIO_EMAC0_RESET (GPIO_OUTPUT | GPIO_CFG_PULLUP | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOC | GPIO_PIN10)
#define IRQ_EMAC0_INT SAM_IRQ_PA14
/* LEDs
*
* A single LED is available driven by PC8.
*/
#define GPIO_LED0 (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOC | GPIO_PIN8)
/* Buttons
*
* SAM E70 Xplained contains two mechanical buttons. One button is the RESET
* button connected to the SAM E70 reset line and the other, PA11, is a generic
* user configurable button. When a button is pressed it will drive the I/O
* line to GND.
*
* NOTE: There are no pull-up resistors connected to the generic user buttons
* so it is necessary to enable the internal pull-up in the SAM E70 to use the
* button.
*/
#define GPIO_SW0 (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_CFG_DEGLITCH | \
GPIO_INT_BOTHEDGES | GPIO_PORT_PIOA | GPIO_PIN11)
#define IRQ_SW0 SAM_IRQ_PA11
/* HSMCI SD Card Detect
*
* The SAM E70 Xplained has one standard SD card connector that is connected
* to the High Speed Multimedia Card Interface (HSMCI) of the SAM E70. SD
* card connector:
*
* ------ ----------------- ---------------------
* SAME70 SAME70 Shared functionality
* Pin Function
* ------ ----------------- ---------------------
* PA30 MCDA0 (DAT0)
* PA31 MCDA1 (DAT1)
* PA26 MCDA2 (DAT2)
* PA27 MCDA3 (DAT3) Camera
* PA25 MCCK (CLK) Shield
* PA28 MCCDA (CMD)
* PC16 Card Detect (C/D) Shield
* ------ ----------------- ---------------------
*/
#define GPIO_MCI0_CD (GPIO_INPUT | GPIO_CFG_DEFAULT | GPIO_CFG_DEGLITCH | \
GPIO_INT_BOTHEDGES | GPIO_PORT_PIOC | GPIO_PIN16)
#define IRQ_MCI0_CD SAM_IRQ_PC16
/* USB Host
*
* The SAM E70 Xplained has a Micro-USB connector for use with the SAM E70 USB
* module labeled as TARGET USB on the kit. In USB host mode VBUS voltage is
* provided by the kit and has to be enabled by setting the "VBUS Host Enable"
* pin (PC16) low.
*/
#define GPIO_VBUSON (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOC | GPIO_PIN16)
/* Click Shield
*
* --- ----- ------------------------------ ---------------------------------
* PIN PORT SHIELD FUNCTION PIN CONFIGURATION
* --- ----- ------------------------------ ---------------------------------
* AD0 PD26 microBUS2 Analog TD PD26 *** Not an AFE pin ***
* AD1 PC31 microBUS2 Analog PC31 AFE1_AD6 GPIO_AFE1_AD6
* AD2 PD30 microBUS2 GPIO reset output PD30
* AD3 PA19 microBUS1 GPIO reset output PA19
* AD4 PC13 (both) I2C-SDA PC13 *** Does not support I2C SDA ***
* AD5 PC30 (both) I2C-SCL PC30 *** Does not support I2C SCL ***
* AD6 PA17 *** Not used ***
* AD7 PC12 *** Not used ***
* D0 PD28 (both) HDR_RX PD28 URXD3 GPIO_UART3_RXD
* D1 PD30 (both) HDR_TX PD30 UTXD3 GPIO_UART3_TXD_1
* D2 PA5 microBUS1 GPIO interrupt input PA5
* D3 PA6 microBUS2 GPIO interrupt input PA6
* D4 PD27 *** Not used ***
* D5 PD11 microBUS2 PWMB PD11 PWMC0_H0
* D6 PC19 microBUS1 PWMA PC19 PWMC0_H2
* D7 PA2 *** Not used ***
* D8 PA17 *** Not used ***
* D9 PC9 microBUS2 CS GPIO output PC9
* D10 PD25 microBUS1 CS GPIO output PD25 SPI0_NPCS1
* D11 PD21 (both) SPI-MOSI PD21 SPI0_MOSI GPIO_SPI0_MOSI
* D12 PD20 (both) SPI-MISO PD20 SPI0_MISO GPIO_SPI0_MISO
* D13 PD22 (both) SPI-SCK PD22 SPI0_SPCK GPIO_SPI0_SPCK
*/
/* Reset (RST#) Pulled-up on the click board */
#define CLICK_MB1_RESET (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOA | GPIO_PIN19)
#define CLICK_MB2_RESET (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOD | GPIO_PIN30)
/* Interrupts. No pull-ups on the BEE; assumig active low. */
#define CLICK_MB1_INTR (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_CFG_DEGLITCH | \
GPIO_INT_FALLING | GPIO_PORT_PIOA | GPIO_PIN5)
#define CLICK_MB2_INTR (GPIO_INPUT | GPIO_CFG_PULLUP | GPIO_CFG_DEGLITCH | \
GPIO_INT_FALLING | GPIO_PORT_PIOA | GPIO_PIN6)
#define IRQ_MB1 SAM_IRQ_PA5
#define IRQ_MB2 SAM_IRQ_PA6
/* SP chip selects */
#define CLICK_MB1_CS (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOD | GPIO_PIN25)
#define CLICK_MB2_CS (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOC | GPIO_PIN9)
#define MB1_CSNO SPI0_CS1 /* GPIO_SPI0_NPCS1_1 */
#define MB2_CSNO SPI0_CS0 /* REVISIT PC9 is not one of the NPCS pins */
/************************************************************************************
* Public Types
************************************************************************************/
/************************************************************************************
* Public data
************************************************************************************/
#ifndef __ASSEMBLY__
/************************************************************************************
* Public Functions
************************************************************************************/
/************************************************************************************
* Name: sam_sdram_config
*
* Description:
* Configures the on-board SDRAM. SAME70 Xplained features one external
* IS42S16100E-7BLI, 512Kx16x2, 10ns, SDRAM. SDRAM0 is connected to chip select
* NCS1.
*
* Input Parameters:
* None
*
* Assumptions:
* The DDR memory regions is configured as strongly ordered memory. When we
* complete initialization of SDRAM and it is ready for use, we will make DRAM
* into normal memory.
*
************************************************************************************/
#ifdef CONFIG_SAMV7_SDRAMC
void sam_sdram_config(void);
#else
# define sam_sdram_config(t)
#endif
/************************************************************************************
* Name: sam_bringup
*
* Description:
* Bring up board features
*
************************************************************************************/
#if defined(CONFIG_LIB_BOARDCTL) || defined(CONFIG_BOARD_INITIALIZE)
int sam_bringup(void);
#endif
/************************************************************************************
* Name: sam_dacdev_initialize
*
* Description:
* Called to configure DAC peripheral module
*
************************************************************************************/
#if defined(CONFIG_SAMV7_DAC0) || defined(CONFIG_SAMV7_DAC1)
int sam_dacdev_initialize(void);
#endif
/************************************************************************************
* Name: sam_spidev_initialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the SAME70-XPLD board.
*
************************************************************************************/
#ifdef CONFIG_SAMV7_SPI
void sam_spidev_initialize(void);
#endif
/************************************************************************************
* Name: sam_hsmci_initialize
*
* Description:
* Initialize HSMCI support
*
************************************************************************************/
#ifdef HAVE_HSMCI
int sam_hsmci_initialize(int slot, int minor);
#else
# define sam_hsmci_initialize(s,m) (-ENOSYS)
#endif
/************************************************************************************
* Name: sam_usbinitialize
*
* Description:
* Called from stm32_boardinitialize very early in initialization to setup USB-
* related GPIO pins for the SAME70-XPLD board.
*
************************************************************************************/
#ifdef HAVE_USB
void sam_usbinitialize(void);
#endif
/****************************************************************************
* Name: sam_can_setup
*
* Description:
* Initialize CAN and register the CAN device
*
****************************************************************************/
#ifdef CONFIG_SAMV7_MCAN
int sam_can_setup(void);
#endif
/************************************************************************************
* Name: sam_netinitialize
*
* Description:
* Configure board resources to support networking.
*
************************************************************************************/
#ifdef HAVE_NETWORK
void sam_netinitialize(void);
#endif
/************************************************************************************
* Name: sam_emac0_setmac
*
* Description:
* Read the Ethernet MAC address from the AT24 FLASH and configure the Ethernet
* driver with that address.
*
************************************************************************************/
#ifdef HAVE_MACADDR
int sam_emac0_setmac(void);
#endif
/************************************************************************************
* Name: sam_cardinserted
*
* Description:
* Check if a card is inserted into the selected HSMCI slot
*
************************************************************************************/
#ifdef HAVE_HSMCI
bool sam_cardinserted(int slotno);
#else
# define sam_cardinserted(slotno) (false)
#endif
/************************************************************************************
* Name: sam_writeprotected
*
* Description:
* Check if the card in the MMCSD slot is write protected
*
************************************************************************************/
#ifdef HAVE_HSMCI
bool sam_writeprotected(int slotno);
#endif
/************************************************************************************
* Name: sam_automount_initialize
*
* Description:
* Configure auto-mounters for each enable and so configured HSMCI
*
* Input Parameters:
* None
*
* Returned Value:
* None
*
************************************************************************************/
#ifdef HAVE_AUTOMOUNTER
void sam_automount_initialize(void);
#endif
/************************************************************************************
* Name: sam_automount_event
*
* Description:
* The HSMCI card detection logic has detected an insertion or removal event. It
* has already scheduled the MMC/SD block driver operations. Now we need to
* schedule the auto-mount event which will occur with a substantial delay to make
* sure that everything has settle down.
*
* Input Parameters:
* slotno - Identifies the HSMCI0 slot: HSMCI0 or HSMCI1_SLOTNO. There is a
* terminology problem here: Each HSMCI supports two slots, slot A and slot B.
* Only slot A is used. So this is not a really a slot, but an HSCMI peripheral
* number.
* inserted - True if the card is inserted in the slot. False otherwise.
*
* Returned Value:
* None
*
* Assumptions:
* Interrupts are disabled.
*
************************************************************************************/
#ifdef HAVE_AUTOMOUNTER
void sam_automount_event(int slotno, bool inserted);
#endif
/************************************************************************************
* Name: sam_writeprotected
*
* Description:
* Check if the card in the MMCSD slot is write protected
*
************************************************************************************/
#ifdef HAVE_HSMCI
bool sam_writeprotected(int slotno);
#else
# define sam_writeprotected(slotno) (false)
#endif
/************************************************************************************
* Name: sam_at24config
*
* Description:
* Create an AT24xx-based MTD configuration device for storage device configuration
* information.
*
************************************************************************************/
#ifdef HAVE_MTDCONFIG
int sam_at24config(void);
#endif
/****************************************************************************
* Name: stm32_mrf24j40_initialize
*
* Description:
* Initialize the MRF24J40 device.
*
* Returned Value:
* Zero is returned on success. Otherwise, a negated errno value is
* returned to indicate the nature of the failure.
*
****************************************************************************/
#ifdef HAVE_MRF24J40
int sam_mrf24j40_initialize(void);
#endif
/****************************************************************************
* Name: stm32_xbee_initialize
*
* Description:
* Initialize the XBee device.
*
* Returned Value:
* Zero is returned on success. Otherwise, a negated errno value is
* returned to indicate the nature of the failure.
*
****************************************************************************/
#ifdef HAVE_XBEE
int sam_xbee_initialize(void);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_SAME70_XPLAINED_SRC_SAME70_XPLAINED_H */
Reference in a new issue View git blame Copy permalink