The value returned by sizeof(struct note_start_s) is larger
than the actual memory footprint of struct note_start_s.
This causes the length calculated in sched_note_start to be larger
than the actual memory size,which further leads to out-of-bounds reads in note_common.
Signed-off-by: guohao15 <guohao15@xiaomi.com>
The loopback network driver sending task is placed in the LPWORK queue, which may result in delayed scheduling when the CPU usage reaches 100%, leading to the timely sending of cached messages from the loopback network driver and causing issues with post waitsem being too late.we decied to set loopback sending task to the HPWORK queue.
Signed-off-by: wangchen <wangchen41@xiaomi.com>
avoid packet processing delays caused by task switching,
to support those applications that are extremely time-sensitive.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
Add MTD driver for Winbond W25N series SPI NAND flash.
Currently supports W25N01GV (1Gbit/128MB).
Features:
- Standard SPI interface with configurable frequency (up to 104 MHz)
- Hardware ECC enabled by default
- Block erase with sleep-based wait (releases SPI bus)
- Page read/write with busy-wait for fast operations
Limitations:
- No bad block management (BBM). Factory bad blocks and runtime bad
blocks are not tracked.
- No bad block table (BBT) scanning at initialization.
- No Quad SPI support (standard SPI only).
- No access to spare area (64 bytes/page) or OTP region.
Tested using:
- Board with STM32H743
- W25N01GV on SPI at 96 MHz with DMA enabled
- Flash mounted using littlefs
- Tested using sdbench:
- Sequential write speed of 1760 KB/s
- Sequential read speed of 4900 KB/s
Signed-off-by: Julian Oes <julian@oes.ch>
Add handling for GPIOC_SETDEBOUNCE to set GPIO pin debounce duration.
Add handling for GPIOC_SETMASK to enable/disable GPIO interrupt mask.
Signed-off-by: chenzihan1 <chenzihan1@xiaomi.com>
In order to reduce code duplication, use the eeprom/spi_xx25xx
driver within mtd/at25ee.
The eeprom/xxx.h includes have been merged into eeprom/eeprom.h, to
provide a common include file like mtd/mtd.h.
Signed-off-by: Antoine Juckler <6445757+ajuckler@users.noreply.github.com>
Changed the DRIVERS_VIRTIO_INPUT dependencies from 'depends on' to 'select'
for INPUT_TOUCHSCREEN, INPUT_KEYBOARD, and INPUT_MOUSE options. This ensures
that when DRIVERS_VIRTIO_INPUT is enabled, all required input subsystems are
automatically selected, fixing the issue where mouse device nodes were not
being created properly.
Signed-off-by: rongyichang <rongyichang@xiaomi.com>
When the setinterface interface is called, it indicates that the underlying
USB link has been successfully established. At this point, the status of the
network card needs to be updated to RUNNING by calling the netdev_carrier_on
interface. It is similar to the logic after a Wi-Fi network card is
connected to a hotspot. Otherwise, an incorrect network card status may
cause packets to fail to be successfully sent.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
Move mutex lock before checking flist to prevent race condition where
events could be lost when occurring simultaneously with service opening.
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
O_NONBLOCK open mode was broken since
https://github.com/apache/nuttx/pull/17360
MIN() comapres signed value (int) with unsigned value (size_t) which causes
an unexpected return value when ret is negative
Signed-off-by: raiden00pl <raiden00@railab.me>
Upperhalf supports multiple working modes at the same time,
which is specified by NIC when register
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
Remove the previously supported polling mode. If necessary in the
future, switch to a new solution for implementation.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
it will block other works of the list of hpwork when it waits to get buffer for too long. so use a separate workqueue for rpmsgdev.
Signed-off-by: liaoao <liaoao@xiaomi.com>
When using the serial framework buffer, if the buffer is full, excess
data is cached in the usb req buffer. The CDCACM driver doesn't know
when the upper layer will read data from the serial buffer, so it
needs to periodically check if the cached data can be put into the
serial buffer. However, when using zero-copy, each usb req buffer
needs to be completely read before actively switching to the next
req buffer, so the timer is not needed to assist to query.
Signed-off-by: yangsong8 <yangsong8@xiaomi.com>
