This commit introduces basic support for running NuttX on
main domain R5F core of TI AM67 chips, including irq, mpu, pinmux,
timer, and serial configurations. Currently only UART console is
supported. NuttX can be loaded into R5F core from U-Boot or Linux
via RemoteProc.
Co-authored-by: Emre Cecanpunar <emreleno@gmail.com>
Co-authored-by: Abdullah Türkmen <abdullahturkmen@protonmail.com>
Co-authored-by: Muhammet Onur Bayraktar <mobayraktar@t3gemstone.org>
Co-authored-by: Bayram Akay <bakay@t3gemstone.org>
Signed-off-by: Erkan Vatan <evatan@t3gemstone.org>
Introduce minimal chip support for the STMicro STM32N6 family
(Cortex-M55, ARMv8.1-M with TrustZone and FPU), sufficient to bring
up an NSH console over USART1.
Scope (deliberately minimal first drop):
- Chip selector ARCH_CHIP_STM32N6 wired into arch/arm/Kconfig and
chip-name mapping ("stm32n6").
- Sub-Kconfig under arch/arm/src/stm32n6 with the STM32N657X0 chip
selector and a single user-selectable USART (USART1).
- Boot path: stm32_start with a naked dispatcher that clears the
boot-ROM MSPLIM/PSPLIM stack limits before any compiler-emitted
prologue, then runs vector relocation and SRAM-only heap init.
The chip runs entirely in the Secure state; SAU is left in its
reset configuration.
- PLL1-based clock tree fed from HSI64 targeting 200 MHz CPU, with
USART1 kernel-clock routed to HSI for a predictable BRR that is
independent of any later clock change.
- Low-level USART driver with full serial framework support.
stm32_serial.c is adapted from arch/arm/src/stm32h5/stm32_serial.c
(sibling ARMv8-M Mainline port with the same USART IP), stripped
of DMA-RX, LPUART, the per-USART2..5 plumbing, RS-485 driver-enable,
TIOCSINVERT/SWAP and HALFDUPLEX paths.
- SysTick system timer.
- GPIO, PWR and RCC helpers.
TrustZone, MPU, I/D-cache and Helium (MVE) are left disabled to
minimise bring-up surface; these will be added in follow-up patches
alongside the drivers that need them.
Signed-off-by: ImBonkers <samuelnlinden@pm.me>
BREAKING: In an effort to simplify NuttX initialization, NSH_ARCHINIT is
removed. board_app_initialize is also removed. BOARD_LATE_INITIALIZE now
performs all board initialization logic, and is by default enabled. All
references to these symbols are removed. BOARDIOC_INIT remains, but will
result in -ENOTTY when called. It is to be removed in a later commit.
Quick fix: Boards relying on NSH_ARCHINIT should now enable
CONFIG_BOARD_LATE_INITIALIZE instead. If the application needs
fine-grained control over board initialization from userspace, the logic
performed by BOARDIOC_INIT may be copied to the board_finalinitialize
function and used instead via BOARDIOC_FINALINIT. All
board_app_initialize logic provided by NuttX is now moved to
board_late_initialize, and the same should be done for out-of-tree
boards.
Signed-off-by: Matteo Golin <matteo.golin@gmail.com>
The register index layout for D16-D31 and FPU_CONTEXT_REGS was guarded
by CONFIG_ARM_HAVE_DPFPU32 (hardware capability) in three header files,
but all save/restore code in the corresponding .S files gates on
CONFIG_ARM_DPFPU32 (software enable).
These two macros are distinct:
CONFIG_ARM_HAVE_DPFPU32 - set by chip via 'select'; means hardware
has D16-D31 registers
CONFIG_ARM_DPFPU32 - user-selectable; means software has chosen
to use D16-D31 (requires hardware support)
When ARM_HAVE_DPFPU32=y and ARM_DPFPU32=n, the header defined
REG_FPSCR at offset 64 and FPU_CONTEXT_REGS=65, while the assembly
only saved S0-S31+FPSCR (33 words), placing FPSCR at offset 32.
This mismatch causes incorrect register access and wrong xcptcontext
sizing.
Signed-off-by: yaojiaqi <yaojiaqi@lixiang.com>
arch/arm/include/imx6/irq.h looks to originally be for i.MX6 Quad
and includes multiple (re)definitions of IRQ names, some of which are
different or don't exist on i.MX6 SoloLite/Solo/Dual/DualLite.
Update irq.h to specify/reserve IRQ names/numbers as defined by the
IM6SDLRM, IMX6DLRM, and IMX6DQRM reference manuals.
Signed-off-by Peter Barada <peter.barada@gmail.com>
Document the HT32F491x3 ESK32 board, build steps,
flashing flow, and validation commands. Add WSL and
PowerShell flash backends plus a Python wrapper.
Signed-off-by: Felipe Moura <moura.fmo@gmail.com>
Add initial HT32F491x3 support with startup, IRQ handling,
serial console, GPIO helpers, custom vectors, and CMake build files.
Signed-off-by: Felipe Moura <moura.fmo@gmail.com>
Rename STM32_IRQ_NEXTINT to STM32_IRQ_NEXTINTS across all stm32
variants.
In stm32_dumpnvic() dynamically print NVIC enable and priority
registers based on STM32_IRQ_NEXTINTS.
Use PRIx32 format specifier instead of 'x' (since uint32_t on arm is
actually a long unsigned int).
Simplify if/else chain in stm32_irqinfo() to determine irq reg/bit.
There's no stm32_irqinfo.c; remove mention in stm32f0l0g0/Make.defs.
Signed-off-by Peter Barada <peter.barada@gmail.com>
Rename IMX9_IRQ_uSDHC{1,2,3} to IMX9_IRQ_USDHC{1,2,3} in both arm
and arm64 imx95_irq.h to follow the all-caps naming convention used
by imx93_irq.h and the rest of the NuttX codebase. Remove the now
unnecessary USDHC IRQ alias block from arm64 imx95_irq.h.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
Add definition to setup appropriate reduced SRAM sizes
CONFIG_STM32H7_STM32H72XXX_OR_STM32H73XXX.
The define should make addition of other STM32H72X
and TM32H73X chips easier.
Signed-off-by: Pavel Pisa <pisa@fel.cvut.cz>
Add hardware register headers and driver support for the NXP i.MX93
Cortex-M33 core. All new and modified code is guarded by
ARCH_CHIP_IMX93_M33 preprocessor defines; existing i.MX95-M7 builds
are unaffected.
New drivers:
- imx9_xcache.c - off core cache init and maintenance
- imx9_ccm.c - generic CCM abstraction layer
Signed-off-by: Maarten Zanders <maarten@zanders.be>
Replace CONFIG_SYSTEM_TIME64 conditional atomic64 operations with a unified
seqlock-based approach for managing the system tick counter. This simplifies
code by eliminating architecture-specific branches and provides more robust
thread-safe access patterns.
Signed-off-by: hujun5 <hujun5@xiaomi.com>
Adds support to select irq line 1 to share the same GPIO with Linux
Also added GPIO5 definiton for IRQ
Signed-off-by: Peter van der Perk <peter.vanderperk@nxp.com>
Rename STACK_ALIGNMENT macro to STACKFRAME_ALIGN throughout the codebase
to provide clearer naming semantics. The new name better reflects the macro's
purpose of frame alignment rather than general stack alignment.
Signed-off-by: hujun5 <hujun5@xiaomi.com>
Use 1u/~1u constants for TPIDRPRW bit operations.
Avoid implicit conversion to a different underlying type (MISRA Rule 10.3).
No functional change to task pointer tagging logic.
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>
Add support to disable signals actions related struct
Co-authored-by: guoshichao <guoshichao@xiaomi.com>
Signed-off-by: Chengdong Wang <wangchengdong@lixiang.com>
1. up_irq_save should not mask fiq if CONFIG_ARCH_HIPRI_INTERRUPT=y
2. up_irq_save should mask fiq if CONFIG_ARCH_TRUSTZONE_SECURE=y
3. up_irq_save should mask irq if CONFIG_ARCH_TRUSTZONE_SECURE=n
4. add up_secure_irq in arm64
5. add ARCH_HAVE_TRUSTZONE support for ARCH_CORTEX_R82
Signed-off-by: hujun5 <hujun5@xiaomi.com>
Add STM32H7_STM32H7X0XX chip family.
Add new chip configurations for STM32H750 variants in Kconfig, update
hardware includes to support CONFIG_STM32H7_STM32H7X0XX, and modify
board configurations for stm32h750b-dk to use STM32H750XB.
This enables support for the new STM32H750 chip series with appropriate
memory and peripheral mappings.
Normalize the defconfig files for boards from stm32f7 chip family.
Signed-off-by: Sergey Rzhevsky <rzsa@yandex.ru>
SAME70J and SAMV70J series (64 pin packages) have two USART peripherals
and three UART peripherals. Ensure USART peripherals are enabled.
This is consistent with datasheet, USART0 also physically tested
on SAME70J21 MCU.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
PIC32CZ CA70 family is pin to pin and binary compatible with
SAMV70/SAME70 families, therefore the support is placed in samv7
directory. The only difference is larger RAM memory compared to SAM
families.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Added subclasses of STM32G0 (such as STM32G07X) to Kconfig for use in dmamux driver. Added definitions to stm32g0_dmamux.h. Added configuration of number of dma and dmamux channels.
Added missing dma mappings for stm32g0.
Remove reserved defines.
Formatting fixes.
Added DMA2 IRQ mappings for STM32G0B and STM32G0C. Changed STM32_DMAMUX_BASE to STM32_DMAMUX1_BASE to align with stm32_dma_v1mux.c and C0 defines.
Provide correct mapping for ADC1_DMA_CHAN. Add STM32F0L0G0_HAVE_ADC1_DMA to STM32G0.
Add support for continuous mode to the ADC. Also added support to set smp1 and smp2 in board.h, as well as smpsel.
Removed unnecessary selects of STM32F0L0G0_STM32G0. Changed board level files to properly define A0-A3 on nucleo-g0b1re.
Add new Kconfig changes.
Made combined configs for STM32G0. Ex. STM32G0BX for STM32G0B0 and STM32G0B1.
Fixed defines and references in Kconfig and stm32_dma_v1mux.c
Defined adc_sampletime_write and adc_sampletime_set. Changed adc_sample_time_s structure to be much simpler. Old way made no sense. You can only have 2 sample times, so defining one for each channel makes no sense. The new adc_sample_time_s contains smp1, smp2, and smpsel. Also define ADC_HAVE_SMPR_SMP2 for STM32C0.
Added adc_sampletime_write and adc_sampletime_set. Altered adc_sample_time_s structure to be more appropriate for g0 and c0. Only two sample times can be defined. Added rcc support for DMA2.
Added defconfig for nucleo-g0b1re:adc_dma config.
Restore correct Kconfig from my original branch
Removed redundant ifdefs. If we select for G0 and C0, we know they have SMP2. Fixed formatting.
Formatting feedback. Aligned columns in irq and dma headers.
The l1entry replace cause huge time when text/data is big,
Need 16KB per task to hold l1table.
Also critical_section no longer required, as table per-task maintained.
For complex goldfish emulator scarios can speed up:
enter_nsh/application_init_done,
from 23.517300/05:07.067500
to 01.501500/00:06.587300
at least 10 times faster.
As we don't have do x_NPAGES swap out etc.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
Add basic support for RA4M1.
The following perpheral are added:
* GPIO
* SCI (UART)
* Clock (Just internal clock - HOCO)
Signed-off-by: leocafonso <leocafonso@gmail.com>
This adds minimal support for NXP MCX-N236 CPU. Peripherals supported are:
- GPIO
- PINMUX
- CLOCK
- LPUART
An example board, FRDM-MCXN236 is also added, with a basic profile that
boots into nsh.
Signed-off-by: Ville Juven <ville.juven@unikie.com>
This fixes below issues when building for PROTECTED mode:
- `common/arm_fork.c:223 'struct xcpt_syscall_s' has no member 'cpsr'`
- `armv7-r/arm_syscall.c:454 'xcptcontext' has no member 'sigreturn'`
Signed-off-by: Yanfeng Liu <p-liuyanfeng9@xiaomi.com>
This revise armv7-r/ header files needed to support QEMU cortex-r5
virtual process for armv7-r family.
Signed-off-by: Yanfeng Liu <p-liuyanfeng9@xiaomi.com>
copied over files, not modified properly yet
Squashing lots of define errors to get ethernet.c working
quick path rename
Fix STM32_EMAC_BASE (and ICACHE/DCACHE Bases). Enable ETH, ETHTX, and ETHRX with CONFIG_STM32H5_ETHMAC (like H7 does).
Fixed stm32_get_uniqueid
Previously, an exception occurred as a result of calling this function. The problem turned out to be this line: uniqueid[i] = *((uint8_t *)(STM32_SYSMEM_UID) + i);. Dereferencing a 32-bit register as a 8-bit register seemed to be causing this issue. I think this function is better anyway, fewer register accesses and loop iterations.
Turn on SBS peripheral when using Ethernet
The SBS peripheral is required to be turned on because the ETH_SEL_PHY bits need to be set. Without turning this on, RMII mode is not possible. MII may not work either.
Style Updates
