Add a kernel build with OP-TEE/SMC driver enabled to
i.MX93 EVK (target imx93-evk:koptee). Since this is
derived from the 'knsh' target, it is also preconfigured
for use with AHAB boot (see
https://spsdk.readthedocs.io/en/latest/examples/ahab/imx93/imx93_ahab_uboot.html).
Signed-off-by: George Poulios <gpoulios@census-labs.com>
This commit introduces initial support for the Seeed Studio XIAO ESP32C6
board. Five configurations are available:
- nsh: Basic NuttShell support over UART0
- usbnsh: Basic NuttShell support over USB
- gpio: NuttShell over USB + GPIO
- wifi: NuttShell over USB + Wifi support
Signed-off-by: Rodrigo Sim <rcsim10@gmail.com>
The board has got only 64KB of flash, and is on the limit. Removing printf floating point
support frees up ~3kB of flash.
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
The .progmem section in the .text section contains data marked
to not be copied into RAM and instead used directly from program
memory. Unlike other sections that naturally align to 2 byte words,
this section may be odd in length.
If this happens, following sections will end up misaligned
and the compilation will fail. This patch forces correct alignment
after the .progmem section end.
This adds the ability to use USART2 as a console if wanting to use
a console without going through the ST-Link VCOM port. This required when
using an external debugger or trace with this board.
Signed-off-by: Tyler Bennett <tbennett@2g-eng.com>
Before this patch, the board nucleo-767zi had just one button available for the
user, which one was not working (there was no /dev/buttons on stm32_bringup.c).
Aditionally, I have changed the stm32_buttons.c to support not only the
built-in button but as well as to another four external buttons.
Modify rtc_data_seg to rtc_slow_seg to fix RTC problems.
The proper location for those is in RTC slow memory.
Signed-off-by: Filipe Cavalcanti <filipe.cavalcanti@espressif.com>
Add kernel build (target imx93-evk:knsh) to i.MX93 EVK.
This target is preconfigured for use with AHAB boot (see
https://spsdk.readthedocs.io/en/latest/examples/ahab/imx93/imx93_ahab_uboot.html)
as a replacement of U-Boot proper (BL33 at EL2), hence
the load address is set to 0x80200000.
Signed-off-by: George Poulios <gpoulios@census-labs.com>
Adds a defconfig for using MPU60x0 and implement the bringup sequence for the I2C IMU.
Signed-off-by: Filipe Cavalcanti <filipe.cavalcanti@espressif.com>
This change affects esp32s2-saola-1 board when optimizations are enabled.
Fixes issue on timer defconfig.
Signed-off-by: Filipe Cavalcanti <filipe.cavalcanti@espressif.com>
script
Add missing flash_qio_mode file in bootloader link script, it will be
used when CONFIG_ESPRESSIF_FLASH_MODE_QIO option is enabled.
Signed-off-by: Leo Chung <gewalalb@gmail.com>
script
Add missing flash_qio_mode file in bootloader link script, it will be
used when CONFIG_ESPRESSIF_FLASH_MODE_QIO option is enabled.
Signed-off-by: Leo Chung <gewalalb@gmail.com>
script
Add missing flash_qio_mode file in bootloader link script, it will be
used when CONFIG_ESPRESSIF_FLASH_MODE_QIO option is enabled.
Signed-off-by: Leo Chung <gewalalb@gmail.com>
Changed usbhost stack sizes to 2048 for affected STM32H7 boards.
This was previously causing stack overflows when usb is inserted.
Signed-off-by: keever50 <kevinwit1999@gmail.com>
Nimble defconfig had USB Serial as default console. This changes makes it compatible
to ESP32C3-Devkit and makes it similar to other defconfigs.
Signed-off-by: Filipe Cavalcanti <filipe.cavalcanti@espressif.com>
This commit introduces initial support for the Seeed Studio XIAO ESP32C3
board. Five configurations are available:
- nsh: Basic NuttShell support over UART0
- usbnsh: Basic NuttShell support over USB
- gpio: NuttShell over USB + GPIO
- wifi: NuttShell over USB + Wifi support
- ble: NuttShell over SUB + Bluetooth support
Signed-off-by: Rodrigo Sim <rcsim10@gmail.com>
This commit adds support for the LCD based on ST7735 controller on
the STM32F401RC-RS485 board and updates the board documentation accordingly.
Signed-off-by: Rodrigo Sim <rcsim10@gmail.com>
This commit adds sections used by the debugger and disassembler to
get more information about raw data present in the code.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
This commit sets the coexiram (from libcoexist.a) sections on IRAM.
Before this commit, no other rules matched such sections and the
sections could be placed outside markers that denote the end of the
text sections, causing unexpected errors.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
This adds new fields to the metadata section used by MCUBoot.
The openocd-esp32 project requires these fields to properly map the
flash segments and enable using SW breakpoints and flash through
openocd-esp32.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
This adds new fields to the metadata section used by MCUBoot.
The openocd-esp32 project requires these fields to properly map the
flash segments and enable using SW breakpoints and flash through
openocd-esp32.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
This adds new fields to the metadata section used by MCUBoot.
The openocd-esp32 project requires these fields to properly map the
flash segments and enable using SW breakpoints and flash through
openocd-esp32.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
This adds new fields to the metadata section used by MCUBoot.
The openocd-esp32 project requires these fields to properly map the
flash segments and enable using SW breakpoints and flash through
openocd-esp32.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
This adds new fields to the metadata section used by MCUBoot.
The openocd-esp32 project requires these fields to properly map the
flash segments and enable using SW breakpoints and flash through
openocd-esp32.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
This adds new fields to the metadata section used by MCUBoot.
The openocd-esp32 project requires these fields to properly map the
flash segments and enable using SW breakpoints and flash through
openocd-esp32.
Signed-off-by: Tiago Medicci Serrano <tiago.medicci@espressif.com>
Adds adc defconfig and board support for: esp32c3-generic, esp32c6-devkitc and esp32h2-devkit.
Signed-off-by: Filipe Cavalcanti <filipe.cavalcanti@espressif.com>
