Embedded flash can have user signature area on SAMv7. This is a 512
bytes large page whose data are not erased by asserting ERASE pin or by
software ERASE command.
This commit adds arch to board interface for this area. It is possible
to perform read, write and erase operation. SAMV7_USER_SIGNATURE option
has to be set in the configuration.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
By default U(S)ART clocks are enabled in sam_lowput.c but
configuration check from sam_config.h may override USART configuration
and prevent clocks from been enabled.
This commit fix inconsistency in U(S)ART pinmux and clock configuration
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Make channels synchronous (i.e. share the same timebase) with the help
of SAMV7_PWMx_CHy_SYNC defines. All the channels share the same
timebase of channel 0, so this channel must be defined too.
Signed-off-by: Stepan Pressl <pressste@fel.cvut.cz>
Option CONFIG_SENSORS_QENCODER might be configured even if SAMv7 qencoder
over timer counter is not used (for example encoder over GPIO is selected
with CONFIG_SAMV7_GPIO_ENC). This can cause compile warnings, also build
of sam_qencoder.c file is unnecessary in that case.
New hidden option CONFIG_SAMV7_QENCODER is added and automatically
selected if at least one timer counter is enabled for qencoder. Build
is triggered on this option.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
PWMx_CHy_LONLY options have been added to Kconfig, too.
If LONLY is selected, it's not possible to use complementary outputs.
If LONLY is not selected, it's possible to use H or complementary
output. If configured correctly with cpol and dcpol attributes,
a H-like behaviour can be achieved. May be useful when you run out
of free MCU pins.
Signed-off-by: Stepan Pressl <pressste@fel.cvut.cz>
The SAMV7's qencoder driver now supports the GETINDEX ioctl call
which does not reset the internal Timer/Counter and returns
the current position, position of the last index and the number
of captured indexes to a struct qe_index_s pointer. Because the
SAMV7's timers are 16bit, the extension to 32 bits must be done.
Select CONFIG_SAMV7_QENCODER_ENABLE_GETINDEX in the Kconfig to
enable this functionality.
This driver does not obey the instructions given in the ATSAMV7
2023 datasheet because the recommended trigger resets the internal
counter which is not desired. Instead, a capture into capture A
and capture B registers is used. This way if an event happens
(the rising edge of the index signal), the current counter's value
is captured.
Signed-off-by: Stepan Pressl <pressste@fel.cvut.cz>
This commit adds support for TX DMA transfers for USART peripheral. Code
refactor in sam_serial.h was also required in order to have correct
defines for all possible cases (both RX and TX DMA used, just one used,
none used).
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
SAMv7 reset controller stores the cause of last reset (SW reset, power up,
pin reset etc.) in status register. This commit adds function that allows
the board to retrieve this information. This function should be called
from board support layer either during initialization or based on
incoming ioctl call.
Adding the sam_get_reset_cause() to sam_systemreset.c also resulted in
always compiling this file by default and only putting up_systemreset()
under CONFIG_SAMV7_SYSTEMRESET option.
Also header file sam_systemreset.h was created as it defines reset types
in comfortable manner for future processing in board layer. This is done
to avoid passing boardctl dependent structure to architecture layer.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Commit 03e5c02 introduced option to have both standard SPI and QSPI
in SPI mode on one system. However this change broke the appearance of
QSPI driver configuration menu entry in menuconfig as it was dependent
on !SAMV7_QSPI_IS_SPI (which is now true for all MCUs having standard
SPI ability in QSPI driver).
This change makes sure the menu is correctly shown when QSPI driver
used.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit refactors DAC driver. The functionality remains the same
but driver start up is now done in dac_setup (after application called
open function) instead of sam_dac_initialize (called from BSP). This
ensures that driver does not take resources (timer, interrupt) until
opened. Implementation of dac_shutdown is also provided, therefore
the driver frees resources once closed.
This change is consistent with other drivers implementation.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
USART peripheral can work in SPI mode as well. This commit adds support
for such functionality. Only 1 slave device is supported by the
peripheral therefore board level does not have to ensure correct CS
setup.
The usage of the peripheral is the same as with other SPI drivers.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
The `xxx_ipv6multicast` function in each driver is not adapted to
multiple IPv6 addresses yet, and they're redundant, so try to take them
into common code.
Change:
1. Add MAC `g_ipv6_ethallnodes` and `g_ipv6_ethallrouters` in
`icmpv6_devinit` and call them in `netdev_register`
2. Add multicast MAC for Neighbor Solicitation when adding any IPv6
address, and remove them when IPv6 address is removed
3. Select `NET_MCASTGROUP` when `NET_ICMPv6` because now we need
`d_addmac` when we have ICMPv6
Note:
We want modules outside net stack to call functions like
`netdev_ipv6_add` and never touch the related MAC address, so these MAC
functions are added as internal functions to `net/netdev/netdev.h`
Signed-off-by: Zhe Weng <wengzhe@xiaomi.com>
Add registration function instrumentation API,
which can achieve instrumentation of entering and
exiting functions through the compiler's functionality.
We can use CONFIG_ARCH_INSTRUMENT_ALL to add instrumentation for all
source, or add '-finstrument-functions' to CFLAGS for Part of the
source.
Notice:
1. use CONFIG_ARCH_INSTRUMENT_ALL must mark _start or entry noinstrument_function,
becuase bss not set.
2. Make sure your callbacks are not instrumented recursively.
use instrument_register to register entry function and exit function.
They will be called by the instrumented function
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
chip/sam_emac.c:3754:11: error: 'struct sam_emac_s' has no member
named 'phytype'
3754 | if (priv->phytype == SAMV7_PHY_KSZ8061)
| ^~
make[3]: *** [Makefile:167: sam_emac.o] Error 1
Member phytype is available only if CONFIG_NETDEV_PHY_IOCTL and
CONFIG_ARCH_PHY_INTERRUPT is set.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit adds support for 1 wire interface over serial driver. SAMv7
MCU does not have build in one wire support therefore external hardware
still has to be used (connection of RX/TX for example).
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
UART/USART peripheral can be used for more than just standard serial
driver. It can for example be used for 1 wire interface communication
(with external circuitry added). This changes the Kconfig for SAMv7 to
allow future implementation of these drivers. Now user can select
what kind of a driver he wants on UART/USART (serial or something else).
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
The typo s/.timid/.tcid prevents to compile NuttX with
quadrature encoder configured for timer1 (CONFIG_SAMV7_TC1_QE)
and s/SAM_TC789_BASE/SAM_TC678_BASE prevented use of the
of the timer 2.
Signed-off-by: Pavel Pisa <ppisa@pikron.com>
This change fixes the issue when SAMv7 GMAC sometimes does not start packet
transmission. The issue is that EMAC_NCR_TSTART is written to EMAC_NCR register
while tx descriptor is not delivered to memory.
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Some SD card connectors do not have separate card detection pin. In that
case card detection has to be done on CD/DAT3 data line. This means
software (i.e. architecture level driver) has to take care of pin
configuration switching (pin has to be set as data pin in case of
transfer and as interrupt card detection pin when there is no action
on data line).
This commit adds CD/DAT3 line card detection support for SAMv7 MCU.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Current implementation of QSPI in SPI mode was available only for MCUs
that do not have standard SPI at all. MCUs with both QSPI and SPI can
however also use QSPI in SPI mode and thus have one more SPI bus. This
commit adds required defines and config options to support QSPI in SPI
mode for all SAMv7 MCUs.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit adds function pwm_set_polarity() that setups channel
polarity based on input info from application layer.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This small fix ensures all DMA pointers are correctly reseted during
DMA setup (when the driver is opened). Without this there could be rare
occurrence of driver pointer to incorrect (invalidate) DMA buffer and thus
saving incorrect characters to upper layer.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Circular buffer does not use DMA linked list therefore function
sam_freelinklist() cannot be called as it would fail on assertion (csa
not defined). Peripheral that calls DMA should care of buffer invalidation
instead.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
SAMv7 QSPI peripheral does not copy-in/out directly into/from
user provided buffer, but use a dedicated memory that is interfaces
using byte copy. The QSPI command buffer can point to memory with
any alignment
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
This commit adds deifiniton of get_timer_period() and adj_timer_period()
functions used by adjtime() interface.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
