This change fixes NuttX’s CMake support when NuttX is embedded
in another project via add_subdirectory(). CMake’s CMAKE_SOURCE_DIR
and CMAKE_BINARY_DIR refer to the outermost project, causing NuttX
to access its .config, generated files, host tools, and build artifacts
in the parent project’s directories. The fix introduces NUTTX_DIR and
NUTTX_BINARY_DIR, based on CMAKE_CURRENT_SOURCE_DIR and
CMAKE_CURRENT_BINARY_DIR, and consistently uses them for NuttX
self-references while preserving existing standalone builds. It fixes
the Kconfig initialization failure reported in #19697 and allows an
embedded sim:nsh build to configure, build, and boot successfully.
The change affects only the CMake build system (not Make or Kconfig
defaults), requires the corresponding nuttx-apps change, and does not
extend add_subdirectory() support to cross-compiled non-sim boards due
to CMake’s toolchain-file limitation.
Fixes#19697.
Assisted-by: Claude:claude-sonnet-5
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
update:
CMakeLists.txt
Make.defs
Kconfig
It allows the same version of SystemView target sources to be used for CMake and Make, to avoid discrepancies in the future.
Signed-off-by: simbit18 <simbit18@gmail.com>
This commit provided a better recursive spinlock implementation with
less memory-overhead and better performance.
Signed-off-by: ouyangxiangzhen <ouyangxiangzhen@xiaomi.com>
we are using segger RTT protocol over shared memory for two core log/trace: one is NuttX another Linux/Windows. But the base address of shared memory can only be known at runtime, so we change SEGGER_RTT_UNCACHED_OFF from macro to global variable, and update to the correct g_segger_offset after the shared memory is initialized by:
g_segger_offset = (uintptr_t)ishmem - (uintptr_t)&_SEGGER_RTT;
Signed-off-by: liwenxiang1 <liwenxiang1@xiaomi.com>
Add a configuration option CONFIG_SEGGER_SYSVIEW_POST_MORTEM to enable
logging continuously into a circular buffer
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
Don't assume that perf_getfreq returns nanoseconds, define the
SEGGER_SYSVIEW_TIMESTAMP_FREQ instead.
Signed-off-by: Jukka Laitinen <jukka.laitinen@tii.ae>
Most tools used for compliance and SBOM generation use SPDX identifiers
This change brings us a step closer to an easy SBOM generation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Add heap current used to note.
Plot it in segger sysview data plot.
Signed-off-by: xuxingliang <xuxingliang@xiaomi.com>
Signed-off-by: Neo Xu <neo.xu1990@gmail.com>
sched implementation not depends on macro abstraction, so revert below commit:
This reverts commit 4e62d0005a
This reverts commit 0f0c370520
This reverts commit ad0efd04ee
Signed-off-by: chao an <anchao@lixiang.com>
In SMP mode, up_cpu_index()/this_cpu() are the same, both return the index of the physical core.
In AMP mode, up_cpu_index() will return the index of the physical core, and this_cpu() will always return 0
| #ifdef CONFIG_SMP
| # define this_cpu() up_cpu_index()
| #elif defined(CONFIG_AMP)
| # define this_cpu() (0)
| #else
| # define this_cpu() (0)
| #endif
Signed-off-by: chao an <anchao@lixiang.com>
usage:
1. Connect Jlink, start JLinkGDBServer
JLinkGDBServer -if SWD -device stm32h743zi -speed 16000
2. Listen to the RTT port data and forward it to the virtual serial port
sudo socat -d -d PTY,link=/dev/ttyRTT0,raw,ignoreeof TCP:127.0.0.1:19021,reuseaddr
3. Read serial data
minicom -D /dev/ttyRTT0
Performance:(STM32H743, 400MHZ)
time "dd if=/dev/zero of=/dev/console bs=512 count=2048"
6.67 sec 157KB/s
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
1. Update all CMakeLists.txt to adapt to new layout
2. Fix cmake build break
3. Update all new file license
4. Fully compatible with current compilation environment(use configure.sh or cmake as you choose)
------------------
How to test
From within nuttx/. Configure:
cmake -B build -DBOARD_CONFIG=sim/nsh -GNinja
cmake -B build -DBOARD_CONFIG=sim:nsh -GNinja
cmake -B build -DBOARD_CONFIG=sabre-6quad/smp -GNinja
cmake -B build -DBOARD_CONFIG=lm3s6965-ek/qemu-flat -GNinja
(or full path in custom board) :
cmake -B build -DBOARD_CONFIG=$PWD/boards/sim/sim/sim/configs/nsh -GNinja
This uses ninja generator (install with sudo apt install ninja-build). To build:
$ cmake --build build
menuconfig:
$ cmake --build build -t menuconfig
--------------------------
2. cmake/build: reformat the cmake style by cmake-format
https://github.com/cheshirekow/cmake_format
$ pip install cmakelang
$ for i in `find -name CMakeLists.txt`;do cmake-format $i -o $i;done
$ for i in `find -name *\.cmake`;do cmake-format $i -o $i;done
Co-authored-by: Matias N <matias@protobits.dev>
Signed-off-by: chao an <anchao@xiaomi.com>
