optimize the current code format according to the previous net_xxx_wait
implementation to reduce multiple calls of similar code
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
reduce the execution consumption of irrelevant code
testing the TX rates of TCP and UDP based on the Infineon board can
increase them by 13%.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
This reverts commit 696a94c8055dc59933457e8ce5c3c91dbecab980
first, when continuous ping from tester to vela, if ignore arp expire when ping response use arp_out to build L2 layer, this cause TC13 testing arp entry expire feature failed. second, the patch of support queue iob when arp_out failed can fix this bug.
Signed-off-by: wenquan1 <wenquan1@xiaomi.com>
Improve the behavior of the ARP table so that the manually configured
ARP table has the highest priority, can only be manually modified to
other values, otherwise will never change again, and will not time out.
The modified behavior is consistent with that of Linux.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
if update is called after tx, in an environment with very low
latency (such as a simulator), the received arp_response will
be overwritten by update (NULL), resulting in arp learning success,
but the packets are always not sent correctly and are converted
into arp packets.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
Wait a fixed number of milliseconds before sending a retry ARP request for the same destination if the IP address mapping is not exist to prevent ARP flooding
Signed-off-by: wenquan1 <wenquan1@xiaomi.com>
If arp search fails once, subsequent searches for the ip will directly
return failure, and sends an asynchronous arp request to try to update
arp table in the future. In this way, the psock_sendmsg interface will
not block for a long time each time because arp cannot be obtained.
This scenario is triggered when a udp socket frequently attempts to
access an ip address that does not exist on the LAN.
Signed-off-by: zhanghongyu <zhanghongyu@xiaomi.com>
Most tools used for compliance and SBOM generation use SPDX identifiers
This change brings us a step closer to an easy SBOM generation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Summary:
- In arp_send(), arp_wait_setup() adds a notify object to g_arp_waiters
which is removed in arp_wait() in normal case.
- However, in timeout and error cases, the object was not removed and
caused memory corruption.
- This commit fixes this issue.
Impact:
- None
Testing:
- Tested with spresense:rndis_smp
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
1.Consolidate absolute to relative timeout conversion into one place(_net_timedwait)
2.Drive the wait timeout logic by net_timedwait instead of devif_timer
This patch help us remove devif_timer(period tick) to save the power in the future.
Change-Id: I534748a5d767ca6da8a7843c3c2f993ed9ea77d4
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
Normally it is required that the network be in the "down" state when re-configuring the network interface. This is thought not to be a necessary here because.
1. The ICMPv6 logic here runs with the network locked so there can be no outgoing packets with bad source IP addresses from any asynchronous network activity using the device being reconfigured.
2. Incoming packets depend only upon the MAC filtering. Network drivers do not use the IP address; they filter incoming packets using only the MAC address which is not being changed here.
sched/semaphore: Add nxsem_post() which is identical to sem_post() except that it never modifies the errno variable. Changed all references to sem_post in the OS to nxsem_post().
sched/semaphore: Add nxsem_destroy() which is identical to sem_destroy() except that it never modifies the errno variable. Changed all references to sem_destroy() in the OS to nxsem_destroy().
libc/semaphore and sched/semaphore: Add nxsem_getprotocol() and nxsem_setprotocola which are identical to sem_getprotocol() and set_setprotocol() except that they never modifies the errno variable. Changed all references to sem_setprotocol in the OS to nxsem_setprotocol(). sem_getprotocol() was not used in the OS
libc/semaphore: Add nxsem_getvalue() which is identical to sem_getvalue() except that it never modifies the errno variable. Changed all references to sem_getvalue in the OS to nxsem_getvalue().
sched/semaphore: Rename all internal private functions from sem_xyz to nxsem_xyz. The sem_ prefix is (will be) reserved only for the application semaphore interfaces.
libc/semaphore: Add nxsem_init() which is identical to sem_init() except that it never modifies the errno variable. Changed all references to sem_init in the OS to nxsem_init().
sched/semaphore: Rename sem_tickwait() to nxsem_tickwait() so that it is clear this is an internal OS function.
sched/semaphoate: Rename sem_reset() to nxsem_reset() so that it is clear this is an internal OS function.
