Add basic timer operations to the kernel, including registration,
start/stop, and callback handling. This provides a consistent timer
interface for use by kernel components and drivers.
Signed-off-by: zhaohaiyang1 <zhaohaiyang1@xiaomi.com>
Introduce a single configuration option to provide strict transmit
priority ordering based on CAN ID.
The intention is to expose the user-visible behavior (strict TX
priority ordering) rather than the underlying implementation details.
Strict priority ordering is only meaningful when hardware transmit
buffer cancellation is available, so splitting this functionality into
separate configuration options was misleading and could result in
partially effective or incorrect configurations.
Signed-off-by: zhaohaiyang1 <zhaohaiyang1@xiaomi.com>
These documentation updates correspond to commits:
- drivers/capture: add signal notification support for edge capture events
- drivers/capture: add fake capture driver for testing and development
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
This moves mtd.rst from special/ directory to its own special/mtd
subdirectory and adds pages for supported devices (NOR/NAND flashes and
EEPROMS) with some basic configuration and initialization description.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Add handling for GPIOC_SETDEBOUNCE to set GPIO pin debounce duration.
Add handling for GPIOC_SETMASK to enable/disable GPIO interrupt mask.
Signed-off-by: chenzihan1 <chenzihan1@xiaomi.com>
Add support for the page erase (PE), sector erase (SE) and chip erase
(CE) dedicated commands on supported devices.
They can be triggered using the corresponding IOCTL commands
EEPIOC_PAGEERASE, EEPIOC_SECTORERASE and
EEPIOC_CHIPERASE.
On unsupported devices, this is equivalent to writing a full page,
sector, or the entire EEPROM to 0xFF.
Signed-off-by: Antoine Juckler <6445757+ajuckler@users.noreply.github.com>
Add EEPIOC_SETSPEED ioctl acting like the MTDIOC_SETSPEED ioctl. The
default frequency is settable in the Kconfig.
Add xx25xx SPI delay control configurations.
Signed-off-by: Antoine Juckler <6445757+ajuckler@users.noreply.github.com>
This adds ability for read and write operations to work with messages
aligned to configured number of bytes. This has few different use
cases.
The alignment is specified as unsigned integer and can be changed with
ioctl command CANIOC_SET_MSGALIGN. The current value can be queried by
CANIOC_GET_MSGALIGN command.
The default value for the message alignment is 1. This will provide
behavior consistent with current one. Thus messages are placed to the
buffer right after data of the previous one. The same applies for
writes.
The special alignment value 0 disables read and write of multiple frames. Thus
read will always return at most one message and write will always write
only one message even if larger buffer size is provided.
Another use case is if message alignment is set to exactly message
representation size (`sizeof(struct can_msg_s)`). This allows writing
and reading arrays of messages.
Other values provide even more advanced and specialized use cases, such
as optimizations if architecture has to emulate some non-aligned
accesses, there alignment of for example 4 bytes could provide
performance boost.
The original motivation behind this is was compatibility with socket
CAN. It is easier to port applications to NuttX's CAN driver if only one
frame is provided at the time. This solution was suggested by Pavel Pisa
<pisa@fel.cvut.cz> as a more versatile variant of plain boolean
disabling the multiple frame retrieval.
Signed-off-by: Karel Kočí <kkoci@elektroline.cz>
Add documentation for changes made in #16809.
Add an example defconfig for a nsh build with the capture example.
Replace the STM32H7_CAP option with just CAPTURE as the guard for the
lower half driver.
Signed-off-by: Côme VINCENT <44554692+comejv@users.noreply.github.com>
This commit creates a sbutton device that uses a single button to
create a keyboard driver that returns TAB or ENTER depending how
long the user keeps the button pressed.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
Updates the ADS1115 documentation with information about the two new
commands for triggering conversion and reading the result.
Signed-off-by: Matteo Golin <matteo.golin@gmail.com>
This commit adds the missing documentation for the ioctl command ANIOC_ADS1115_READ_CHANNEL.
Signed-off-by: Tony Lin <99093620+justapotato213@users.noreply.github.com>
The MCP47X6 series consists of the following single channel DAC chips:
- MCP4706 (8 bit)
- MCP4716 (10 bit)
- MCP4726 (12 bit)
The driver supports the following configurations:
- gain
- power down
- voltage reference
Persistent configuration storage in the internal EEPROM is not
implemented.
This commit adds the documentation for the Texas Instruments ADS1115 Driver.
Signed-off-by: Tony Lin <99093620+justapotato213@users.noreply.github.com>
Adds initial documentation to the IOCTL commands of wireless character devices.
Signed-off-by: Kevin Witteveen (MartiniMarter) <kevinwit1999@gmail.com>
Added detailed information about the SX126x and its current state in development.
Added directories for wireless character driver and LPWAN.
Added indexes to each directory and its contents within.
Signed-off-by: Kevin Witteveen (MartiniMarter) <kevinwit1999@gmail.com>
This ioctl clears the active fault inputs. Some faults can be latched
(still active even if the source is not active anymore), so they have
to be cleared from the software. The argument is a pointer to unsigned
long bitmask variable. This bitmask specifies which faults are to be
cleared.
The ioctl also can fetch the faults active prior to the clear. These
faults are saved to the argument specifying which faults are to be
cleared. Therefore passing zero bitmask means the driver will only return
active faults and clear none. Passing NULL pointer means the driver
will clear all active and return none.
The implementation of this ioctl is per driver.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This commit add support to the serial_icounter_s struct used with
TIOCGICOUNT to report U[S]ART errors such as frame, parity, overrun,
etc.
Signed-off-by: Alan C. Assis <acassis@gmail.com>
This adds basic API description for ADC and DAC peripherals. External
ADC/DAC controllers are listed as well.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
There are ICs available on the market that integrate various power inverter
features. The driver for such a device must be tightly coupled to a FOC device
as using it as a separate device doesn't make sense.
