Permissions (Part 2)
Description:
In kernel builds, any unprivileged process running on the NuttX
device can open /dev/efuse and attempt to read/write fuse content.
Reading the fuses may provide valuable information to an attacker
controlling the user process. The write operation, in extreme cases
where the fuse blocks are not locked, may brick the device.
DISCLAIMER: I tried to be strict with the settings, better to relax them
later if it's needed.
This is part of https://github.com/apache/nuttx/issues/19410
See https://github.com/apache/nuttx/issues/19410
Compiles ok.
Signed-off-by: Catalin Visinescu <catalin_visinescu@yahoo.com>
debug.h is a NuttX-specific, non-POSIX header. Placing it in the
top-level include/ directory creates naming conflicts with external
projects that define their own debug.h.
This commit moves the canonical header to include/nuttx/debug.h,
following the NuttX convention for non-POSIX/non-standard headers,
and updates all in-tree references.
A backward-compatibility shim is left at include/debug.h that
emits a deprecation #warning and re-includes <nuttx/debug.h>,
allowing out-of-tree code to continue building while migrating.
Signed-off-by: Piyush Patle <piyushpatle228@gmail.com>
Most tools used for compliance and SBOM generation use SPDX identifiers
This change brings us a step closer to an easy SBOM generation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Although the LED might be RGB-only, the LED data is packed in a
32-bit long variable and, then, this is the default size of a LED
pixel to define the 'WS2812_RW_PIXEL_SIZE' macro. Please note that
the lower-half driver will deal with the case of the addressable
LED being 3 or 4-pixel sized.
- Add mmap into file_operations and remove it from ioctl definitions.
- Add mm_map structure definitions to support future unmapping
- Modify all drivers to initialize the operations struct accordingly
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
1.Don't check the return value of nxsem_init or nxmutex_init
2.Fix some style issue
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
0c3db448bb
added the option to generate the waveforms to drive ws2812 and similar LEDs using different
hardware (e.g. RP2040 PIO instead of SPI).
For that new mode, the concept of CONFIG_WS2812_FREQUENCY is different. Instead of
the SPI frequency (commonly a few MHz), it is the frequency of the actual output waveform
(commonly 400 or 800 kHz).
There was an attempt to express the SPI frequency divided by 10, but it's not actually the
case either (it would be divided by 8).
I think it is clearer to explain in Kconfig what CONFIG_WS2812_FREQUENCY means for each mode
and go back to the previous behaviour for the original SPI mode (also to avoid breaking
out-of-tree boards).
It's not necessary to send a reset pulse after sending the RGB data
since the first thing that a new transmission does is sending the long
reset pulse. I have left 1 reset byte after the RGB data to keep some
padding given that the bits inside the byte are shifted by 1 bit although
I think it wouldn't be necessary either. But just in case.
This reduces the memory usage (you can easily save 60 bytes) and increases
the maximum refresh rate.
Previously only 4 MHz and 8 MHz were allowed. Given the tolerance
allowed in the WS2812 timing spec, frequency ranges around those
two can be used too which is useful for boards in which it is
difficult to generate those specific frequencies.
The WS2812 is very common in LED strips as it is an integrated
controller and LED. It is driven by a single data line, but
the timing requirements can be met by using most SPI controllers
and the use of DMA.
This driver has been validated on the nRF52 arch both with a
single LED and a strip of 144.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
