Only in the non-critical region， nuttx can the respond to the irq and not hold the lock
When returning from the irq, there is no need to check whether the lock needs to be released
we also need keep restore_critical_section in svc call
test:
Configuring NuttX and compile:
$ ./tools/configure.sh -l qemu-armv8a:nsh_smp
$ make
Running with qemu
$ qemu-system-aarch64 -cpu cortex-a53 -smp 4 -nographic \
-machine virt,virtualization=on,gic-version=3 \
-net none -chardev stdio,id=con,mux=on -serial chardev:con \
-mon chardev=con,mode=readline -kernel ./nuttx
Signed-off-by: hujun5 <hujun5@xiaomi.com>
armv7-m/arm_mpu.c: In function 'mpu_dump_region':
armv7-m/arm_mpu.c:621:13: warning: format '%X' expects argument of type 'unsigned int', but argument 4 has type 'long unsigned int' [-Wformat=]
621 | _info("MPU-%d, alignedbase=0%08X l2size=%"PRIu32" SRD=%X"
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
armv7-m/arm_mpu.c:621:13: warning: format '%X' expects argument of type 'unsigned int', but argument 6 has type 'long unsigned int' [-Wformat=]
621 | _info("MPU-%d, alignedbase=0%08X l2size=%"PRIu32" SRD=%X"
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
armv7-m/arm_mpu.c:621:13: warning: format '%X' expects argument of type 'unsigned int', but argument 7 has type 'long unsigned int' [-Wformat=]
621 | _info("MPU-%d, alignedbase=0%08X l2size=%"PRIu32" SRD=%X"
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
armv7-m/arm_mpu.c:621:13: warning: format '%u' expects argument of type 'unsigned int', but argument 8 has type 'long unsigned int' [-Wformat=]
621 | _info("MPU-%d, alignedbase=0%08X l2size=%"PRIu32" SRD=%X"
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>
Modified the input parameters of mpu_initialize to require the caller to provide the number of entries in the table
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
In a multicore task scenario, there may be a situation where the task runs on different cores at different time slices (when the task is not bound to a particular core).
When the task calls cache clean/flush(range > cache size), depending on the optimization, clean_all, flush_all are called. however, at this point, there may be dirty data or incomplete data profiles in the cache on the kernel that is running the task, which may result in dirty data being flushed into memory or make the application think that the flushed data should be successfully flushed into memory, leading to unknown consequences.
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
Execute data and instruction sync barriers after writing MPU register,
to ensure MPU setting take effects that the new changes are seen.
testing in lm3s6965-ek:qemu-protected
Signed-off-by: fangxinyong <fangxinyong@xiaomi.com>
Pass CP15_CACHE_INVALIDATE argument with r1 register to cp15_dcache_op_level.
cache level is 0(L1 D-Cache) with r0 register.
prototype:
void cp15_dcache_op_level(uint32_t level, int op)
Signed-off-by: Jinliang Li <lijinliang1@lixiang.com>
according to armv6-m/armv7-m arch reference manual:
the three ISB {<opt>}, DSB {<opt>}, DMB {<opt>} instructions <opt>
field are defined as:
Specifies an optional limitation on the ISB/DSB/DMB operation. Allowered
values are:
Full system ISB/DSB/DMB operation, encoded as option=='1111'. Can be
omitted.
All other encodings of the options are RESERVED.
the "#opt" field of "isb #opt"
So we could remove the options field in Armv7-m platform.
The following are the build error with greenhills compiler:
CC: common/arm_exit.c [asarm] (error #2071) /tmp/gh_001h70j1.si 92: bad parameter
isb 15
------^
[asarm] (error #2071) /tmp/gh_001h70j1.si 112: bad parameter
isb 15
------^
[asarm] (error) errors during processing
According to armv8-m arch reference manual:
the ISB/DMB instruction's "opt" encoding rule is same as
armv6-m/armv7-m, but the "DSB" instruction is different, in armv8-m, the
"DSB {<opt>}" field has two valid encoding options: 0b0000, 0b0100.
and all other encoding options are reserved.
In Armv7-a/Armv8-a, the dsb/dmb option field has 8 valid state value.
Signed-off-by: guoshichao <guoshichao@xiaomi.com>
This adds the necessary defines to set the USARTs' kernel clock source
selection.
This is required for a configuration where the bootloader (running
before NuttX) changes the USARTs' clock selection, so they need to be
restored on board init.
This is according to the reference manual RM0399 page 448.
when the thread to backtrace is exiting, get_tcb and up_backtrace in
different critical section may cause try to dump invalid pointer, have
to ensure the nxsched_get_tcb and up_backtrace inside same critical
section procedure.
Signed-off-by: buxiasen <buxiasen@xiaomi.com>
The following warnings is fixed:
chip/sam_pwm.c:961:12: warning: unused variable 'regval' [-Wunused-variable]
961 | uint32_t regval;
chip/sam_serial.c: In function 'sam_dma_txavailable':
chip/sam_serial.c:2264:7: warning: unused variable 'rv' [-Wunused-variable]
2264 | int rv;
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Larger RX/TX buffers might be required for both FD and FD_BSW modes.
Default bit timing values are also changed since the original ones
did not provide correct results for default SAMv7 board clock selection
(150 MHz clock frequency). The current values provide correct bit timing
with sample point as close to 87.5 %.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
This adds field type to canioc_bittiming_s structure that allows
to set/obtain bit timing for both CAN CC and CAN FD.
CANIOC_GET_BITTIMING is now bidirectional: user specifies type field
and gets other fields from the controller.
The commit also updates current CAN FD capable controllers using the
ioctl. The type is not checked for classical CAN only controllers
and nominal bit timing is returned regardless of type value.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
