This commit introduces the tagging system into the STM32 family of chips
by tagging all chips with their appropriate chip type/family.
Signed-off-by: Matteo Golin <matteo.golin@gmail.com>
Introduces `sphinx-tags` to the documentation system, allowing
individual pages to be tagged for better searching. The examples in this
commit introduce the `chip:*` tag for indicating the chip a board uses,
as well as the `experimental` tag for indicating experimental boards and
features. Other tags indicate supported peripherals for boards, such as
`wifi` and `ethernet`.
Signed-off-by: Matteo Golin <matteo.golin@gmail.com>
This commit adds support for the LCD based on ST7735 controller on
the STM32F401RC-RS485 board and updates the board documentation accordingly.
Signed-off-by: Rodrigo Sim <rcsim10@gmail.com>
Renaming "modlib" to "libelf" is more in line with the implementation content,
which makes it easier for individual developers to understand the capabilities of this module.
CONFIG_LIBC_MODLIB -> CONFIG_LIBC_ELF
Signed-off-by: chao an <anchao.archer@bytedance.com>
This commit adds support for the BMP180 sensor on the
STM32F401RC-RS485 board and updates the board documentation
accordingly. It also enables the BMP180 UORB driver in the
STM32 common logic.
Signed-off-by: Rodrigo Sim <rcsim10@gmail.com>
Use configuration CDCACM_DISABLE_TXBUF or CDCACM_DISABLE_RXBUF to choose
whether to use usb req buffer as the serial buffer. Since the default
value is n (not using req buf), the original configuration of buf is valid.
This reverts commit 21c8ed80bd.
add discard-data=on in proxy launch command, so the proxy side
will clean the share memory to make sure that the shared memory is clean
every time server and proxy are started.
Signed-off-by: Bowen Wang <wangbowen6@xiaomi.com>
Add documentation for nucleo-h563zi development board.
Removed whitespace at the end of lines.
Fixed column formatting.
Fixed Title overline too short error.
Added image to nucleo-h563zi documentation.
An example implementation for OpenAMP based on the Inter-VM share memory(ivshmem)::
rpproxy_ivshmem: Remote slave(client) proxy process.
rpserver_ivshmem: Remote master(host) server process.
Signed-off-by: chao an <anchao.archer@bytedance.com>
So far only USART drivers could use TX/RX DMA. This commit adds the
support for UART drivers as well (with the exception of serial console).
UART peripheral does not have timeout interrupt, so external polling
is required to flush the RX data from DMA buffers even if the buffer
is not yet full. The board layer can do this by calling
sam_serial_dma_poll function.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Previously, the LVGL example had a workaround in lv_nuttx_fbdev.c to prevent
video memory invasion. This fix properly addresses the issue by:
- Reducing total SDRAM size from 8MB to 6MB
- Moving LTDC base address to 0xC0600000
- Reserving dedicated space for video memory outside NuttX heap
This ensures proper memory separation between video buffer and system heap.
Signed-off-by: Jorge Guzman <jorge.gzm@gmail.com>
- Add support for the IMX95LPD5EVK-19 evaluation kit (M7 core only)
- Firmware can be executed from ITCM, DDR or NOR flash
- configurations:
'nsh' A minimal configuration that only enables nsh shell
on a UART
'rpmsg' This configuration is similar to nsh but in addition
it offers the Remote Processing Messaging (RPMsg) service to
enable heterogeneous inter-core communication.
Split nucleo-f4x1re into nucleo-f401re and nucleo-f411re.
These are separate boards and should be in separate directories as it's
done for all other nucleo boards in NuttX
