diff --git a/arch/arm/src/stm32h5/Kconfig b/arch/arm/src/stm32h5/Kconfig index 634872840bc..3a1e04d36ab 100644 --- a/arch/arm/src/stm32h5/Kconfig +++ b/arch/arm/src/stm32h5/Kconfig @@ -1408,8 +1408,8 @@ endchoice # FDCAN1 mode menu "FDCAN1 Bit Timing" config STM32H5_FDCAN1_AUTO_BIT_TIMING - bool "FDCAN1 Automatic Bit Timing" - default y + bool "FDCAN1 Automatic Bit Timing" + default y ---help--- Automatically determine FDCAN1 bit timing (nominal and data) based on bitrate. @@ -1426,7 +1426,7 @@ config STM32H5_FDCAN1_NTSEG1 int "FDCAN1 NTSEG1 (PropSeg + PhaseSeg1)" default 6 range 1 256 - depends on !STM32H5_FDCAN1_AUTO_BIT_TIMING + depends on !STM32H5_FDCAN1_AUTO_BIT_TIMING ---help--- The length of the bit time is Tquanta * (SyncSeg + PropSeg + PhaseSeg1 + PhaseSeg2). @@ -1434,7 +1434,7 @@ config STM32H5_FDCAN1_NTSEG2 int "FDCAN1 NTSEG2 (PhaseSeg2)" default 7 range 1 128 - depends on !STM32H5_FDCAN1_AUTO_BIT_TIMING + depends on !STM32H5_FDCAN1_AUTO_BIT_TIMING ---help--- The length of the bit time is Tquanta * (SyncSeg + PropSeg + PhaseSeg1 + PhaseSeg2). @@ -1442,7 +1442,7 @@ config STM32H5_FDCAN1_NSJW int "FDCAN1 synchronization jump width" default 1 range 1 128 - depends on !STM32H5_FDCAN1_AUTO_BIT_TIMING + depends on !STM32H5_FDCAN1_AUTO_BIT_TIMING ---help--- The length of the bit time is Tquanta * (SyncSeg + PropSeg + PhaseSeg1 + PhaseSeg2). @@ -1535,8 +1535,8 @@ endchoice # FDCAN2 mode menu "FDCAN2 Bit Timing" config STM32H5_FDCAN2_AUTO_BIT_TIMING - bool "FDCAN2 Automatic Bit Timing" - default y + bool "FDCAN2 Automatic Bit Timing" + default y ---help--- Automatically determine FDCAN2 bit timing (nominal and data) based on bitrate. @@ -1553,7 +1553,7 @@ config STM32H5_FDCAN2_NTSEG1 int "FDCAN2 NTSEG1 (PropSeg + PhaseSeg1)" default 6 range 1 256 - depends on !STM32H5_FDCAN2_AUTO_BIT_TIMING + depends on !STM32H5_FDCAN2_AUTO_BIT_TIMING ---help--- The length of the bit time is Tquanta * (SyncSeg + PropSeg + PhaseSeg1 + PhaseSeg2). @@ -1561,7 +1561,7 @@ config STM32H5_FDCAN2_NTSEG2 int "FDCAN2 NTSEG2 (PhaseSeg2)" default 7 range 1 128 - depends on !STM32H5_FDCAN2_AUTO_BIT_TIMING + depends on !STM32H5_FDCAN2_AUTO_BIT_TIMING ---help--- The length of the bit time is Tquanta * (SyncSeg + PropSeg + PhaseSeg1 + PhaseSeg2). @@ -1569,7 +1569,7 @@ config STM32H5_FDCAN2_NSJW int "FDCAN2 synchronization jump width" default 1 range 1 128 - depends on !STM32H5_FDCAN2_AUTO_BIT_TIMING + depends on !STM32H5_FDCAN2_AUTO_BIT_TIMING ---help--- The length of the bit time is Tquanta * (SyncSeg + PropSeg + PhaseSeg1 + PhaseSeg2). diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig index bc9acd8a90a..38349d6af49 100644 --- a/arch/arm64/Kconfig +++ b/arch/arm64/Kconfig @@ -118,7 +118,7 @@ config ARCH_CHIP_BCM2711 select ARCH_NEED_ADDRENV_MAPPING select ARCH_HAVE_MULTICPU select ARCH_USE_MMU # Required for up_testset - select ARMV8A_HAVE_GICv2 + select ARMV8A_HAVE_GICv2 ---help--- Broadcom BCM2711 quad-core ARM Cortex A72 diff --git a/arch/arm64/src/bcm2711/Kconfig b/arch/arm64/src/bcm2711/Kconfig index 0b9f667f4ca..70fbfeed9dd 100644 --- a/arch/arm64/src/bcm2711/Kconfig +++ b/arch/arm64/src/bcm2711/Kconfig @@ -14,80 +14,80 @@ comment "BCM2711 configuration options" menu "Broadcom BCM2711 Peripheral Selection" config BCM2711_LOW_PERIPHERAL - bool "BCM2711 Low Peripheral Mode" - default y - ---help--- - Use the Broadcom BCM2711 in low peripheral addressing mode. + bool "BCM2711 Low Peripheral Mode" + default y + ---help--- + Use the Broadcom BCM2711 in low peripheral addressing mode. ##################################################################### # I2C Configuration (master) ##################################################################### config BCM2711_I2C - bool "I2C Master" - select I2C - ---help--- - Support for I2C in master mode. + bool "I2C Master" + select I2C + ---help--- + Support for I2C in master mode. if BCM2711_I2C config BCM2711_I2C0 - bool "I2C0" - default n - ---help--- - Enable the I2C0 interface. - See board selection menu to configure the pins used by I2C0. + bool "I2C0" + default n + ---help--- + Enable the I2C0 interface. + See board selection menu to configure the pins used by I2C0. config BCM2711_I2C1 - bool "I2C1" - default n - ---help--- - Enable the I2C1 interface. - See board selection menu to configure the pins used by I2C1. + bool "I2C1" + default n + ---help--- + Enable the I2C1 interface. + See board selection menu to configure the pins used by I2C1. config BCM2711_I2C2 - bool "I2C2" - default n - ---help--- - Enable the I2C2 interface. - See board selection menu to configure the pins used by I2C2. + bool "I2C2" + default n + ---help--- + Enable the I2C2 interface. + See board selection menu to configure the pins used by I2C2. config BCM2711_I2C3 - bool "I2C3" - default n - ---help--- - Enable the I2C3 interface. - See board selection menu to configure the pins used by I2C3. + bool "I2C3" + default n + ---help--- + Enable the I2C3 interface. + See board selection menu to configure the pins used by I2C3. config BCM2711_I2C4 - bool "I2C4" - default n - ---help--- - Enable the I2C4 interface. - See board selection menu to configure the pins used by I2C4. + bool "I2C4" + default n + ---help--- + Enable the I2C4 interface. + See board selection menu to configure the pins used by I2C4. config BCM2711_I2C5 - bool "I2C5" - default n - ---help--- - Enable the I2C5 interface. - See board selection menu to configure the pins used by I2C5. + bool "I2C5" + default n + ---help--- + Enable the I2C5 interface. + See board selection menu to configure the pins used by I2C5. config BCM2711_I2C6 - bool "I2C6" - default n - ---help--- - Enable the I2C6 interface. - See board selection menu to configure the pins used by I2C6. + bool "I2C6" + default n + ---help--- + Enable the I2C6 interface. + See board selection menu to configure the pins used by I2C6. config BCM2711_I2C_DRIVER - bool "I2C character driver" - default n - select I2C_DRIVER - ---help--- - Support for the I2C character driver at /dev/i2c[N]. Can be used - for I2C bus transfers from application code. This driver is intended - for testing, not for use in any real driver application. + bool "I2C character driver" + default n + select I2C_DRIVER + ---help--- + Support for the I2C character driver at /dev/i2c[N]. Can be used + for I2C bus transfers from application code. This driver is intended + for testing, not for use in any real driver application. endif # BCM2711_I2C @@ -96,24 +96,24 @@ endif # BCM2711_I2C ##################################################################### config BCM2711_SPI - bool "SPI support" - select SPI - ---help--- - Support for SPI interfaces. + bool "SPI support" + select SPI + ---help--- + Support for SPI interfaces. if BCM2711_SPI config BCM2711_SPI1 - bool "SPI1" - default n - ---help--- - Enable the SPI1 interface. + bool "SPI1" + default n + ---help--- + Enable the SPI1 interface. config BCM2711_SPI2 - bool "SPI2" - default n - ---help--- - Enable the SPI2 interface. + bool "SPI2" + default n + ---help--- + Enable the SPI2 interface. endif # BCM2711_SPI diff --git a/arch/risc-v/src/bl808/Kconfig b/arch/risc-v/src/bl808/Kconfig index dcf06528e52..74e0d7031cc 100644 --- a/arch/risc-v/src/bl808/Kconfig +++ b/arch/risc-v/src/bl808/Kconfig @@ -110,8 +110,8 @@ menuconfig BL808_I2C0 bool "I2C 0" default n select I2C - select I2C_DRIVER - select ARCH_HAVE_I2CRESET + select I2C_DRIVER + select ARCH_HAVE_I2CRESET if BL808_I2C0 @@ -133,8 +133,8 @@ menuconfig BL808_I2C1 bool "I2C 1" default n select I2C - select I2C_DRIVER - select ARCH_HAVE_I2CRESET + select I2C_DRIVER + select ARCH_HAVE_I2CRESET if BL808_I2C1 @@ -156,8 +156,8 @@ menuconfig BL808_I2C2 bool "I2C 2" default n select I2C - select I2C_DRIVER - select ARCH_HAVE_I2CRESET + select I2C_DRIVER + select ARCH_HAVE_I2CRESET if BL808_I2C2 @@ -179,8 +179,8 @@ menuconfig BL808_I2C3 bool "I2C 3" default n select I2C - select I2C_DRIVER - select ARCH_HAVE_I2CRESET + select I2C_DRIVER + select ARCH_HAVE_I2CRESET if BL808_I2C3 diff --git a/boards/arm64/bcm2711/raspberrypi-4b/Kconfig b/boards/arm64/bcm2711/raspberrypi-4b/Kconfig index d8640e8d600..da87059d333 100644 --- a/boards/arm64/bcm2711/raspberrypi-4b/Kconfig +++ b/boards/arm64/bcm2711/raspberrypi-4b/Kconfig @@ -5,37 +5,36 @@ if ARCH_BOARD_RASPBERRYPI_4B - choice - prompt "Raspberry Pi 4B RAM size" - default RPI4B_RAM_4GB +choice + prompt "Raspberry Pi 4B RAM size" + default RPI4B_RAM_4GB - config RPI4B_RAM_1GB - bool "1GB RAM" - ---help--- - Support for the 1GB variant of the Raspberry Pi 4B. +config RPI4B_RAM_1GB + bool "1GB RAM" + ---help--- + Support for the 1GB variant of the Raspberry Pi 4B. - config RPI4B_RAM_2GB - bool "2GB RAM" - ---help--- - Support for the 2GB variant of the Raspberry Pi 4B. +config RPI4B_RAM_2GB + bool "2GB RAM" + ---help--- + Support for the 2GB variant of the Raspberry Pi 4B. - config RPI4B_RAM_4GB - bool "4GB RAM" - ---help--- - Support for the 4GB variant of the Raspberry Pi 4B. +config RPI4B_RAM_4GB + bool "4GB RAM" + ---help--- + Support for the 4GB variant of the Raspberry Pi 4B. - config RPI4B_RAM_8GB - bool "8GB RAM" - ---help--- - Support for the 8GB variant of the Raspberry Pi 4B. +config RPI4B_RAM_8GB + bool "8GB RAM" + ---help--- + Support for the 8GB variant of the Raspberry Pi 4B. - endchoice # Raspberry Pi 4B RAM size - - config RPI4B_DEBUG_BOOT - bool "Raspberry Pi 4B bootloader debug output" - default n - ---help--- - Enables the debug output of the Raspberry Pi 4B bootloader. +endchoice # Raspberry Pi 4B RAM size +config RPI4B_DEBUG_BOOT + bool "Raspberry Pi 4B bootloader debug output" + default n + ---help--- + Enables the debug output of the Raspberry Pi 4B bootloader. endif # ARCH_BOARD_RASPBERRYPI_4B